English; Getting Started - Electrolux EDBS3350 Mode D'emploi

ENGLISH

Thank you for choosing an Electrolux product. In order to ensure the best results, always use original Electrolux
accessories and spare parts. They have been designed especially for your product. This product is designed with
the environment in mind. All plastic parts are marked for recycling purposes.
Dear Customer,
It may be possible that your steam station does not produce steam immediately after filling it with water for the
first time or refilling the tank. The reason for this is that air trapped in the inner system can delay this function a few
seconds. Please be patient and try it again by pressing the steam button. For your convenience the steam will appear
after you release the steam button for a few seconds and it is not necessary to press the button all the time. Find out
your rhythm for the best steaming result. Thank you for your kind attention and please enjoy your new steam station!
COMPONENTS
A. Steam button
B. Soft handle
C. Temperature alignment mark
D. Temperature selector
E. Temperature indicator light
F. Hot water pipe
G. Mains cable
H. Base unit
I. Anti-calc cartridge
J. Water tank
Picture page 2-3

GETTING STARTED

1
Before first Remove all adhesive remains and gently rub with a dampened cloth. Position the steam gen-
erator iron horizontally on the ironing-board or on a heat resistant, secure surface at the same height as an
ironing-board. Unwind and straighten the power cord and the steam cord. When turned on for the first time,
temporary vapours/odours may occur.
2
Remove the water tank by gripping the slot on the underside and pulling it gently away from the base unit. (A)
Detach the anti-calc cartridge and then immerse it in water for more than one minute. (B) Insert the anti-calc
catridge back. Fill the water tank using cold water. It is recommended to use destilled water or a mix of 50%
destilled, 50% tap water. Empty the water tank to rinse out any foreign particles which may remain from the
manufacturing process.
3
Always refill the water tank to MAX level using cold water (A). Insert the water tank into the base unit (B). It is
recommended to use destilled water or a mix of 50% destilled, 50% tap water. Ensure that the water tank latches
securely into place.
4
Connect the steam generator iron to the mains supply. Press the power button (A). Turn the temperature selec-
tor clockwise to maximum setting (B). The temperature indicator light on the iron will illuminate. Then, select a
steam level on the control panel, from low - medium - high steam.
5
When the temperature indicator light turns on, the steam station is pre-heating. When the light turns off, it
is ready to be used. Press and hold the steam button for about one minute to get steam. Then hold one more
minute in order to clean the steam generating system.
6
Iron an old towel, to ensure that any residues inside the iron are not transferred to the laundry. If necessary, wipe
the sole plate with a slightly damp cloth.
OPERATING INSTRUCTIONS
7
Connect the steam generator iron to the mains supply. Press the power button. When the power switch is
pressed, the power indicator will illuminate. Wait for one to two minutes, until the steam lamp lluminates. Select
the steam level between Low - Medium and High. See Ironing chart for ironing recommendation.
8
If the lower water level indicator is illuminated (A) (followed with two beep sounds), refill the water tank. After
refilling the water tank, press the refill reset button (B). The refill reset button will be extinguished. Steam can
now be used again.
9
To activate the steam, press the steam button. When releasing the button, use up the steam before putting it
back on the iron rest of the steam station.
www.electrolux.com
K. Maximum water level indicator
L. Stainless steel soleplate
M. Iron rest
N. Power indicator light
O. Descaling indicator light
P. Low level water indicator light
Q. Steam level indicator light (Low, Medium, High)
R. Refill reset button
S. Power button
T. Steam level control button
6