Extension Cord; Technical Data - Sunex Tools 5001A Instructions D'utilisation

EXTENSION CORD

When using this tool at a considerable distance from power source, a
conductor, grounding-type extension cord of adequate size must be used
for safety, and to prevent loss of power and over-heating. For a 120 volt
tool, the minimum size of the wires in any extension cord up to 75 feet long
must be 18 gauge (American Wire Gauge) if the total extension cord length
is from 75 to 100 feet, 16 gauge wire is required throughout the exten sion.
NOTE: 16 gauge wire is heavier than 18 gauge and will carry current
for longer distances without a volt age drop.
Use only three wire extension cords which have three prong
grounding type plugs and three hole re cep ta cles which accept the
tools plug. Replace or repair damaged or worn cord immediately.
CHANGING THE GRINDING WHEEL
1. Unplug the bench grinder.
2. Remove the outer wheel guard cover screws and the wheel guard cover.
3. Hold the opposite wheel firmly. Remove the nut and flange.
Note: Turn the spindle nut on the right-hand side counter-clockwise to
loosen. Turn the spindle nut on the left-hand side clockwise to loosen.
4. Remove the old wheel and replace it with the new one.
5. Assemble the flange and nut onto the spindle. Tight en the spindle nut
just enough to hold the wheel firmly. If the nut is tightened too much,
the wheel may be damaged.
6. Attach the wheel guard cover.
7. Turn the grinder on and let it come up to speed and idle for one minute.

TECHNICAL DATA

1. All ball bearing construction for long-lasting reliability.
2. Adjustable, shatterproof eyeshields, spark breakers and tool rest.
3. Accessories of eyeshields, spark breakers, and tool rests are included.
LIMITED WARRANTY:
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY'S SUNEX TOOLS
PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools ® branded products which fail to give satisfactory service due to defective workmanship
or materials, based upon the terms and conditions of the following described warranty plans attributed to that specific product. This product carries a
ONE-YEAR warranty. During this warranty period, Sunex Tools ® will repair or replace at our option any part or unit which proves to be defective in material or
workmanship.
Other important warranty information
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or replacement made
by anyone other than Sunex Tools ® or its authorized warranty service centers. The foregoing obligation is Sunex Tools ® sole liability under this or any implied
warranty and under no circumstances shall we be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Return equipment or parts to Sunex Tools ® , or an authorized warranty service center, transportation prepaid. Be certain to include your name and address,
evidence of the purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write to Sunex Tools ® . This warranty gives you specific legal rights and you may also have other rights
which vary from state to state. Repair kits and replacement parts are available for many of Sunex Tools ® products regardless of whether or not the product is
still covered by a warranty plan.
SHIPPING ADDRESS: Sunex Tools • 315 Hawkins Rd . • Travelers Rest, SC 29690
MAILING ADDRESS: Sunex Tools • P .O . Box 1233 • Travelers Rest, SC 29690
5001A and 5002A: Parts Breakdown and Operating Manual
GROUNDING
This tool should be grounded while in use to protect the operator from
possible electric shock.
1. Cord Connected Tools. This tool should be grounded while in use to
protect the operator from possible electric shock. The tool is equipped
with an approved three conductor cord and three prong grounding type
plug to fit the proper grounding type receptacle. The green (or green
and yellow) conductor in the cord is the grounding wire. Never connect
the green (or green and yellow) wire to a live terminal.
2. Permanently Connected Tools. The tool should be connected to a
grounded metal enclosed wiring system or an equipment grounding
conductor should be run with the circuit conductors and connected to
the equipment grounding terminal or lead on the tool.
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE IS
LONGEST OF THE 3 BLADES
NEVER disassemble the tool or try to do any rewiring in the electric
system. Any such repair should be performed only by a qualified service
organization. Should you be determined to make a repair your self,
remember that the green colored wire is the "ground" wire. Never
connect this green wire to a "live" ter mi nal. If you replace the plug on
the power cord, be sure to connect the green wire only to the ground
(longest) prong on a 3 prong plug.
4
®
BRANDED
rev . 3/13/17