Electrical Warnings - Sunex Tools 5001A Instructions D'utilisation

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
It is the responsibility of the owner to make sure all personnel read
this manual prior to using the device. It is also the responsibility of
the device owner to keep this manual intact and in a convenient
location for all to see and read. If the manual or product labels are
lost or not legible, contact Sunex for replacements. If the operator is
not fluent in English, the product and safety instructions shall be read
and discussed with the operator in the operator's native language by
the purchaser/owner or his designee, making sure that the operator
comprehends its contents.

ELECTRICAL WARNINGS

1. This unit must always be used in accordance with all electrical
and safety codes and ordinances including National Electric Code
(NEC) and Occupational Safety and Health Act (OSHA).
2. Read, study, understand and follow all instructions before using.
3. Failure to follow all instructions listed below may result in electric
shock, fire, explosion and/or serious personal injury.
4. Keep bystanders, children and visitors away while operating unit.
Distractions can cause you to loose control and endanger others.
5. Store unit or product out of reach of children and other untrained
persons, which can become dangerous in the hands of untrained
users.
6. Keep cord away from heat, oil, sharp edges or moving parts.
7. Do not remove any labels. Replace any damaged labels.
8. Slipping, tripping and or falling while operating product can be
a major cause of serious injury or death. Be aware of cord left on
walking or work surface.
9. Never remove, bypass or modify the grounding prong on any
electrical plug in any way. Do not use any adapter plugs. Check
with a qualified electrician if you are in doubt as to whether the
outlet is properly grounded.
10. Never use cord for carrying, pulling or unplugging the unit or
product.
11. Never attempt to plug in or operate unit or product with defective
or damaged wires, power cord or power cord plug. Have any
defective or damaged parts replaced immediately by an
authorized repair center.
12. Do not use in or around water, damp conditions, on wet surfaces,
wet hands or while standing in water.
13. Do not use unit or product around any flammable material or fuel.
14. Keep unit or product away from hot objects.
15. Ground Fault Circuit Interrupter (GFCI) protection is to be provided
on the circuit(s) or outlet(s) to be used for the wet location portable
luminaries. Receptacles are available having built-in GFCI
protection and are able to be used for this measure of safety.
16. If an extension cord is required:
• Use only "UL Listed" extension cords.
• If you are using the tool outdoors, use an extension cord rated
and marked "For Outdoor Use". Use only an extension cord type
SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW,
SJEW, SJEOW, SJEOOW,SJW, SJOW, SJOOW, SJTW, SJTOW, or
SJTOOW.
• The cord must be of the proper size and type to supply the
correct current to the light without overheating. Otherwise the
extension cord could melt and catch fire, or cause electrical
damage to the light. This light requires the use of an extension
cord of 0 to 12 amps capability (up to 50 feet) with wire size
rated at 16 AWG. Longer extension cords require larger size
wire (smaller AWG number). AWG = American Wire Gauge.
17. Stay alert, watch what you are doing and use common sense
when operating a product. Do not use product while tired or under
the influence of drugs, alcohol or medication. A moment of in
5001A and 5002A: Parts Breakdown and Operating Manual
WARNING
attention while operating the product may result in serious
personal injury.
18. Dress properly. Do not wear loose clothing or jewelry. Contain
long hair. Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught in moving
parts.
19. Avoid accidental starting. Be sure switch is in the locked
or "off" position before plugging product into the units power
source. Carrying product with your finger on the switch or
plugging into power source with the switch "on" invites accidents.
20. Disconnect product from power source or place switch in the
locked or "off" position before making any adjustments,
changing accessories, or storing the product. Such preventative
safety measures reduce the risk of starting the product accidently.
21. Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enable better control in unexpected
situations.
22. If damaged, have the unit or product serviced before using. Many
accidents are caused by poorly maintained products.
23. Do not use (or modify) this product for any other purpose than
that for which it was designed without consulting the
manufacturer's authorized representative.
24. Use only accessories that are recommended by the manufacturer.
Accessories that may be suitable for one product may create a
risk of injury when used on another product.
25. This product may contain one or more chemicals known to the
State of California to cause cancer and birth defects or other
reproductive harm. Wash hands thoroughly after handling.
26. Handling the brass parts of this product will expose you to lead, a
chemical known to the State of California to cause birth defects
and other reproductive harm. Wash hands after handling.
27. Failure to heed these warnings may result in serious or fatal
personal injury and/or property damage.
ADDITIONAL GRINDER WARNINGS
1. Always use guards and eye shields (users and bystanders).
Always wear safety glasses or other eye protection and hearing
protection when operating this tool and keep the eye shields
mounted in their proper position on the wheel guard.
2. Always wear breathing apparatus when using this tool.
3. Replace a cracked wheel immediately. Handle wheels carefully
to avoid bumping or dropping. DO NOT use a grinding wheel that
has been dropped. Before using, inspect each wheel for cracks or
flaws and if these are evident, discard the wheel.
4. Before mounting a new wheel, be sure that it is marked with an
RPM that is the same as, or higher than, the no load speed of the
RPM RPM RPM
grinder as marked on the nameplate.
5. Never start a grinder with anyone, including the operator, standing
in line with the wheel. After installing a re place ment wheel, stand
to one side and allow it to revolve freely for about one minute.
6. Do not grind on the sides of grinding wheels unless they are the
special wheels designed specifically for this purpose.
7. Do not over tighten wheel nut.
8. Use only flanges furnished with this grinder.
9. Any damaged parts should be replaced with original parts and/or
by a qualified service technician.
10. Bolt Bench Grinder to a bench or pedestal to prevent
movements.
11. Use accessories only in the proper and intended manner.
12. Spark Breakers should be installed perpendicular to the
grinding wheel. If these are not installed properly, it is an
OSHA violation. See picture on page 5.
2 rev . 3/13/17