Important - Lutron Serena CS-EDU3-SYJ Mode D'emploi

Option C: Outside Mount Above Trim
Hold the shade up to the window to make sure it's the
C.1
correct size. Center the shade and mark the trim at each
end of the shade.
Mark the center line for the two
C2
outside brackets, 2 inches in from
the marks you made in step C.1.
* NOTE: Shades wider than 45 inches
(vinyl headrail) or 48 inches (aluminum
headrail) will need a third bracket ( ) 1
3
(included). Install this bracket in the
center of the shade.
Top view of shade wider than 45 inches
or 48 inches
If the shade is wider than 72 inches,
you will need to install a third ( ) and
3
a fourth bracket ( ) (included). Install 1
4
each of these one-third of the way in
from the outer brackets.
Top view of shade wider than 72 inches
Center the brackets with the center
C.3
line, align the top of the brackets with
each other and mark their location,
making sure they are level.
Hold the brackets in position, mark
C.4
the hole locations and then pre-drill
the holes for the screws. Place a
spacer behind each bracket (to ensure
that the shade clears the window trim,
if trim is present).
Place the bracket fl ush against the
C.5
spacer and the wall, aligning the
holes. Drive a screw through the
holes in the bracket and through
the spacer.
Refer to step A.5 to install
C.6
the shade in the brackets.
Side view
Removing the Shade From the Brackets
To completely remove the shade from
1
its brackets, fi rst locate the metal tab on
each bracket. The tab is located where
the shade fabric meets the headrail on
the side closest to the window.
2 in
2 in
Insert a small fl athead screwdriver
2
through the hole in the metal tab so the
tip of the screwdriver is between the
3 headrail and tab.
2
Rotate the screwdriver until the tab
3
releases the headrail. Repeat for each
bracket on the shade.
3 4
Once you have released all tabs, you
2
/ / /
1 1 1
can lift the shade off the brackets.
3 3 3
Cleaning the Fabric
To keep your cellular shades looking
1
their best, regularly brush them with a
feather duster or lightly vacuum them
with a brush-type attachment.
If your shades get a spot of dirt or a stain on
2
them, use a clean, soft cloth and a solution
of mild detergent and warm water (1 part
detergent to 3 parts water) to blot or lightly
rub the spot or stain.

Important:

Be extra careful if you're cleaning a blackout fabric because you could
bracket spacer
permanently crease the fabric.
Also, do not use strong detergents or spot removers, and do not have
your shades professionally dry cleaned.
wall
window
frame
Lutron Electronics Co., Inc. SHADING SOLUTIONS – Eight Year Limited Warranty
Side view
For more information: www.serenashades.com/warranty
Lutron Technical Support
Contact Lutron Technical Support at the numbers provided below or your local Lutron sales
representative with questions concerning the installation or operation of the System or this
Warranty, or to make a warranty claim. Please provide the exact model number when calling.
Lutron and the Sunburst logo are registered trademarks of Lutron Electronics Co., Inc. Serena is a
trademark of Lutron Electronics Co., Inc.
Worldwide Headquarters | USA
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299 USA
TEL: 1.610.282.3800
FAX: 1.610.282.3090
Technical Support: 1.888.445.8063
Toll Free: 1.888.LUTRON1
EMAIL: shadinginfo@lutron.com
WEB: www.lutron.com/serenashades
Europe Headquarters | United Kingdom
Feather duster Vaccum cleaner with
Lutron EA Ltd
brush attachment
6 Sovereign Close
London, E1W 3JF, UK
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
Technical Support: +44.(0)20.7480.6899
FREEPHONE: 0800.282.107
Diluted mild detergent
Asian Headquarters | Singapore
Lutron GL Ltd
Soft cloth
15 Hoe Chiang Road
#07-03
Singapore, 089316
TEL: +65.6220.4666
FAX: +65.6220.4333
Technical Support: 800.120.4491
11/2013
P/N 045356 Rev. E
Number of years from Percentage of cost of replacement
date of shipment parts credited by Lutron
Up to 5 100%
More than 5 but
50%
not more than 8
More than 8 0%