Programming Menu Items; Powersave Mode - Ovention F1400 Manuel D'installation Et D'utilisation

English
Standby Shutdown
Use standby shutdown to put the oven in standby during
extended periods of non-use.
1. Touch and hold the
the touchscreen for one second to
shut down operation and put the
oven into standby.
• The heating elements and
conveyor will shut down.
• The cooling fans will run until the unit is cool.
Shutdown
1. Touch and hold the
second to shut down operation and put the oven into
standby.
2. Move the Power I/O switch to the O (off) position to turn off
the oven.
• The cooling fans will run until the unit is cool. NOTICE:
Do not unplug unit while cooling fans are running.
Damage to unit may occur.

Programming Menu Items

Use the following procedure to change or create custom menu
item settings.
1. Touch and hold the desired menu item on the Menu
Screen for three seconds.
• The Programming
will appear showing a list of
programmable settings.
Top Heat: Heat
level from top
Setting range is 0–100%.
0 = no heat/lightest cook.
100 = highest heat/darkest cook.
Btm Heat: Heat output level from bottom elements.
Setting range is 0–100%. 0 = no heat/lightest cook.
100 = highest heat/darkest cook.
Time: Total time product is in oven chamber. Increasing
belt time will slow down conveyor and create darker
product. Decreasing belt time will speed up conveyor
and create lighter product.
2. Touch the or arrow next to the desired setting to
change the setting.
3. To change the menu item picture, touch the picture. A
screen will appear with the available pictures
a. Touch the desired picture. The touchscreen will return
to the Programming screen and show the new picture.
4. To change or edit the menu item name, touch the name. A
keypad screen will appear.
a. Touch the key to delete the current name.
b. Use the keypad to change or update the menu item
name.
c. Touch the key to save the name and return to the
Programming screen.
5. When all programming is done, touch the
to the Menu screen.
OVFM-0422
icon on
Unit is off
Cooling fan may still operate
F1400
F1XXUI0107
icon on the touchscreen for one
screen
Top Heat 100 %
Btm Heat 100 %
output
Cook Time 90 sec
elements.
icon to return

PowerSave Mode

Ovention Finishing Ovens have a built-in PowerSave mode.
®
This feature significantly reduces heat levels and energy
consumption when the oven has not been used for a specified
period of time or when activated by the operator.
To start PowerSave mode manually during operation:
1. Touch the
• The conveyor belt will speed up
temporarily to clear product from
the oven, and then stop.
• The PowerSave screen will
show on the touchscreen.
To exit PowerSave mode:
1. Touch the
be ready to cook immediately
NOTE: During recovery from PowerSave mode, full heat output
level of the elements will be achieved in approximately
10 minutes, depending on how much the heat output
level was reduced during PowerSave mode.
Adjusting Automatic PowerSave
Use the following procedure to enable/disable the automatic
PowerSave feature as well as make adjustments to its settings.
NOTE: The default setting for the automatic PowerSave feature
is OFF.
1. Touch the
screen will appear.
• Enter the 3-digit password
"248". The Service screen will
PIZZA
appear.
2. Touch POWERSAVE on the
Service screen. The Automatic
PowerSave screen will appear.
3. Make the desired adjustments on the Automatic
PowerSave screen.
• Touch ON to enable automatic
PowerSave. Touch OFF to
disable automatic PowerSave.
• Heat: Touch the
next to the Heat percentage to
change the heat output level of the elements during
PowerSave mode.
• Time: Touch the
to change the number of minutes of inactivity required
before automatic PowerSave is activated.
4. When all adjustments are done, touch EXIT to return to
the Service screen, then EXIT again to return to the Menu
Screen.
9
OPERATION
icon on the Menu screen.
icon on the PowerSave screen. The unit will
icon on the Menu Screen. A password
Service
Firmware
Control
SystemInfo
Version
Automatic PowerSave
Heat
Time
or arrow
or arrow next to the Time value
Powersave Mode
press the leaf
to exit
Usage
FactoryTest
PowerSave
Exit
On Off
35 %
30 mins
EXIT