Table des Matières
Publicité
Liens rapides
IMPORTANT MANUAL
OPERATOR'S MANUAL
MODEL:
PRRT850
REAR TINE TILLER
ALWAYS WEAR EYE PROTECTION DURING OPERATION
Visit our website: www.poulan-pro.com
Do Not Throw Away
WARNING:
Read this Man u al and follow all Warnings
and Safety Instructions. Fail ure to do so
can re sult in serious in ju ry.
423813 10.15.08 Rev. 1 CL
Printed in U.S.A.
Publicité
Table des Matières
Manuels Connexes pour Poulan Pro PRRT850
Sommaire des Matières pour Poulan Pro PRRT850
- Page 1 MODEL: Read this Man u al and follow all Warnings and Safety Instructions. Fail ure to do so can re sult in serious in ju ry. PRRT850 REAR TINE TILLER ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulan-pro.com 423813 10.15.08 Rev.
-
Page 2: Preparation
SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers TRAINING • Never operate the tiller without proper guards, plates, or other safety protective devices in place. • Read the Manual care ful ly. Be thor ough ly fa mil iar with the controls and the proper use of the equip ment. -
Page 3: Table Des Matières
PRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. Gasolina Capacity: 3 Quarts (2.8L) • Follow a regular schedule in maintaining, caring for Unleaded Reg u lar and using your tiller. Oil (API-SG-SL): SAE 30 (Above 32°F) • Follow instructions under “Maintenance”... -
Page 4: Assembly
ASSEMBLY Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. - Page 5 ASSEMBLY UNPACKING CARTON (See Fig. 2) • Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. CAUTION: Be careful of exposed sta ples when handling or disposing of cartoning material. HANDLE ASSEMBLY "UP"...
-
Page 6: Check Tire Pressure
ASSEMBLY CONNECT SHIFT ROD (See Fig. 7) ATTACH CLUTCH CABLE (See Fig. 6) • Insert end of shift rod into hole of shift lever indicator. • Hook end of clutch cable through hole in control bar bracket. • Insert hairpin clip through hole of shift rod to secure. SHIFT HAIRPIN CONTROL BAR... -
Page 7: Operation
OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. - Page 8 OPERATION The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. 00155 HOW TO USE YOUR TILLER TINE OPERATION - WITH WHEEL DRIVE...
-
Page 9: Before Starting Engine
OPERATION • Move throttle control to “FAST” position for deep tilling. • Place shift lever indicator in “F” (forward) position for To cultivate, throttle control can be set at any desired transporting. speed, depending on how fast or slow you wish to •... -
Page 10: To Start Engine
OPERATION ADD GASOLINE TO START ENGINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular un lead ed gasoline with a CAUTION: KEEP TINE CONTROL IN “OFF” PO SI TION WHEN STARTING ENGINE. minimum of 87 octane. - Page 11 OPERATION TILLING HINTS CULTIVATING Cultivating is destroying the weeds between rows to pre- CAUTION: Until you are accustomed to vent them from robbing nourishment and moisture from the handling your tiller, start actual field use plants. At the same time, breaking up the upper layer of with throttle in slow position (mid-way soil crust will help retain moisture in the soil.
-
Page 12: General Recommendations
MAINTENANCE GENERAL RECOMMENDATIONS LUBRICATION CHART The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main tain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller. -
Page 13: Engine Lubrication
MAINTENANCE Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit for maintenance. -
Page 14: Spark Plug
MAINTENANCE COOLING SYSTEM (See Fig. 19) SPARK PLUG Your engine is air cooled. For proper en gine performance Replace spark plugs at the beginning of each tilling sea- and long life keep your engine clean. son or after every 25 hours of use, whichever comes first. •... -
Page 15: Service & Adjustments
SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER • Remove outer side shield by removing nuts “A” and “B”. • Remove inner side shield by removing nuts “C” and “D”. TO ADJUST HANDLE HEIGHT (See Fig. - Page 16 SERVICE AND ADJUSTMENTS TO REPLACE GROUND DRIVE BELT GROUND DRIVE BELT ADJUSTMENT (See Figs. 22 and 23) (See Fig. 23) • Remove belt guard as described in “TO REMOVE BELT For proper belt tension, the extension spring should have GUARD”. about 5/8 inch (16 mm) stretch when drive control bar is in “EN GAGED”...
-
Page 17: Tine Replacement
SERVICE AND ADJUSTMENTS TINE REPLACEMENT • To maintain the superb tilling performance of this ma chine the tines should be checked for sharpness, (See Figs. 24, 25, and 26) wear, and bending, particularly the tines which are next to the transmission. If the gap between the tines CAUTION: Tines are sharp. -
Page 18: Storage
STORAGE Immediately prepare your tiller for storage at the end of the ENGINE OIL season or if the unit will not be used for 30 days or more. Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CAUTION: Never store the tiller with gasoline in the tank inside a build ing where fumes may reach an open flame... -
Page 19: Troubleshooting
TROUBLESHOOTING POINTS Will not start Out of fuel. 1 Fill fuel tank. Fuel valve “OFF” 2 Turn fuel valve to the “ON” position. Engine Switch “OFF” 3 Turn engine switch to the “ON” position. Engine not “CHOKED” properly. 4 See “TO START ENGINE” in Operation section. Engine flooded. -
Page 20: Service Notes
SERVICE NOTES... -
Page 21: Warranty
LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de- fects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due to materials or workmanship. -
Page 22: Parts And Service
For a Parts Manual, go to our website: www.poulan-pro.com/support.asp NOTE: Poulan Pro provides parts and service through its au thor ized dis tribu tors and dealers; there fore, all requests for parts and service should be directed to your local dealer(s). The phi loso phy of Electrolux Home Products is to con tinu ally improve all of its prod ucts.