Mounting The Light - POWER SMITH PTLH59-60 Manuel D'utilisation

IMPORTAnT SAFETY InSTRUCTIOnS
READ AND UNDERSTAND ALL WARNINGS, CAUTIONS
AND OPERATING INSTRUCTIONS BEFORE USING THIS
EQUIPMENT. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
personal injury.
WaRnInG:
not use with an extension cord near water or where water
may accumulate. Keep work light at least 16 feet from
pools and spas. Keep plugs and receptacles dry. Use only
three-wire outdoor extension cords with grounded plugs
and grounded receptacles.
•
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for this light in wet locations. Receptacles are
available having the built-in GFCI protection and are
able to be used for this measure of safety.
•
Use only with an extension cord for outdoor use,
such as an extension cord of cord type: SW, SW-A, SOW,
SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A,
SJOW, SJOW-A, SJTW, SJTW-A, or SJTOW, SJTOW-A.
•
Do not look directly at the lighted lamps to avoid
eye injuries.
•
Always keep the work light away from any
flammable surface or materials.
•
Always check damaged or worn-out parts before
using the work light. Broken parts will affect the work
light operation. Replace or repair damaged or worn
parts immediately. If repairs are needed, consult a
professional electrician.
•
Do not use a pressure washer to clean this product.
•
Do not modify the work light in any way. Unauthorized
modification may impair the function and/or safety and
could affect the life of the product. There are specific
applications for which the work light was designed.
•
Store work light in a secure place out of the reach of
children. Inspect it for good working condition prior to
storage and before re-use.
caUtIon:
•
Keep the metal parts of light away from any live power
source.
•
Prior to installation and maintenance of the light,
disconnect the light from power source to prevent
electric shock.
•
Installing and operating the light in harsh environments
may shorten the lifespan and/or damage the light.
•
Keep the light away from any corrosive substance and
only clean with dry cloth and non-abrasive cleaner.
•
To ensure personal safety, make sure the light is
mounted firmly and securely when installed in a high
position.

MoUntInG tHe LIGHt

caUtIon:
Check to make sure there are no
signs of physical damage to the product when unpacking.
Do not use damaged product.
RISK OF ELECTRIC SHOCK, Do
English
Hanging the Light
Use the locking carabiner (2) included to hang the light.
See FIG 2. Tighten the lock nut arm (5) after the light is
installed.
Make sure the installation location is strong enough to
bear a minimum 66 lb of weight.
Mounting to a Work Light Stand
The light can be mounted to a PowerSmith work light
stand (PATLH59-HS) as shown in FIG 3.
The work light stand is not included and sold separately.
Mounting to a Magnetic Base
The light can be mounted to a PowerSmith magnetic
base (PATLH59-MS) as shown in FIG 3. With a magnetic
base, the light can be attached to any suitable steel or
iron surface.
The magnetic base is not included and sold separately.
Mounting to a Tripod
The light can be mounted to a tripod. Mount the light
to the PowerSmith work light stand (PATLH59-HS) first,
then mount the light with stand to the PowerSmith tripod
(PATP265).
The work light stand and tripod are not included and sold
separately.
cHaInInG poWeR oUtLet
The light is equipped with an on-board power outlet (4-
FIG1) for chaining. Do not overload the outlet. Refer to
Specifications section for outlet power capacity.
tURnInG on/oFF tHe LIGHt
The light has no switch. Plug into power outlet to turn on
the light. Unplug to turn off the light.
WaRnInG:
is unplugged and completely cool before attempting to
clean it.
Your work light requires very little care and maintenance.
Simply clean the lens regularly with a non-abrasive cleaner.
This product is warranted free from defects in material and
workmanship for 5 (Five) years after date of purchase. This
limited warranty does not cover normal wear and tear or
damage from neglect or accident. The original purchaser is
covered by this warranty and it is not transferable. Prior to
returning your product to store location of purchase, please
call the Toll-Free Help Line for possible solutions.
For questions about this or any other PowerSmith™
product,
Please call Toll-Free:
Or visit our website:
www.
powersmithproducts.com
3
OPERATIOnS
MAInTEnAnCE
Always make sure the work light
WARRAnTY
HELP LInE
888-552-8665.