Air Supply; Lubrication - Napa 6-1016 Mode D'emploi

AIR SUPPLY
Whip Hose
Do Not Install
Quick Coupling Nipple
Here
Leader
Hose
Tools of this class operate on
a wide range of air pres s ures.
We recommend that air pressure
mea s ures 90 psig at the air inlet
with the trigger depressed and
no load applied to the tool. Low
pressure (less than 90 psig
6.2 bar) re d uc e s the speed and
performance of all air tools. High
pres s ure (over 115 psig 8.0 bar)
exceeds the rated capacity of the
tool, which will short e n tool life
and could cause injury.
Always use clean, dry air. Dust,
corrosive fumes, and/or water in
the air line will cause damage to
the tool. Drain water from air

LUBRICATION

Lubricate the air motor daily with
NAPA high quality air tool oil. If
no air line oiler is used, run 1/2 oz.
of oil through the tool. The oil can
be squirted into the tool air inlet
or into the hose at the nearest
con n ec t ion to the air supply, then
OPERATION
Always turn off the air supply,
drain hose of air pressure and
detach tool from air supply before
installing, removing or adjusting
any part or accessory on this
tool, or before performing any
maintenance on this tool.
Abrasive disc and Roloc
pads can be mounted providing
their speed rating exceeds the
speed of the Die Grinder. The
shank size of the abrasive disc
and the Roloc backing pad must
®
please revieW all Warning insTrucTions prior To operaTion. save This Man u al for fuTure ref er ence.
6-1016
Nipple
Quick Coupler Oiler
lines and compressor prior to
running tool. Clean the air inlet
filter screen weekly.
The air inlet used for con n ect i ng
air supply, has stan d ard 1/4" NPT
American Thread. Line pressure
should be increased to compensate
for unusually long air hoses (over
25 feet). Minimum hose diameter
should be 3/8" I.D. Fittings should
have the same inside dimensions
and should be tightly secured.
Ensure an accessible emergency
shut off valve has been installed in
the air supply line and make others
aware of its location.
run the tool. A rust inhibitive oil is
acceptable for air tools. Overfilling
will cause a re d uc t ion in the power
of the tool.
WARNING: After an air tool has
been lubricated, oil will discharge
match the spindle fitted to the Die
Grinder.
After mounting the Roloc
pad and abrasive disc, start the
Die Grinder under bench and
run for a few seconds. If the Die
Grinder starts to vibrate when first
backing mounting the Roloc
®
and abrasive disc, immediately
remove from service. If Die Grinder
is dropped, replace abrasive disc
and Roloc

Air Supply

Filter
Regulator
Drain Daily
backing
®
backing pad
®
backing pad.
®
3
S
pecificationS
Max. Free Speed ............. 20,000 RPM
Collet Size ....................................1/4"
Roloc ® Pad Size ..............................2"
Air Inlet ............................... 1/4" NPT
Min. Hose Size ..................... 3/8" I.D.
Avg. Air Cons. ......................... 3 CFM
Recom. Air
Pressure ....................90 psig (6.2 bar)
Weight .................................... 1.1 lbs.
Length ..........................................6.6"
Sound Level ..........................107 dBA
Vibration Level ...............6.92 M/SEC²
Throttle
Air Inlet
through the exhaust port during
the first few seconds or operation.
The exhaust port must be covered
with a towel before applying air
pressure to prevent serious injury.
When using the Die Grinder, be
careful not to exert excessive force
which could be hazardous and
cause mounted spindle or Roloc
backing pad to bend or break.
NOTE: During operation, safety
goggles must always be worn to
guard against flying rust and chips
(users & bystanders).
®
Rev. 9/9/14