Turning Power On; Important - Stanley IntelliSensor Pro METAL Mode D'emploi

ILLUSTRATION 2
Unit is
Calibrating
Scanning mode
CALIBRATING STUD
Calibration READY METAL
complete 1"–1/2" SCAN
Ready to scan
Depth Mode
Live Wire Low Battery
Indicator
ILLUSTRATION 3
A B
C
38mm
C
A = Wood or metal stud depth detection up to 1/2"
B = Wood or metal stud depth detection up to 1"
C = Wood or metal stud depth detection up to 1-1/2"
D E
METAL
STUD
SCAN
D = Stud scan mode
E = Metal scan mode
3
4.0 Selecting Scanner Depth Mode
1. Depress and hold "ON" button once (1x) to
select to 1/2" read depth detection. The 1/2"
mode LED will illuminate (illustration 2). The
unit will then calibate, followed by a beep
and a green LED will illuminate.
2. Double-click / Depress and hold ON button
twice (2x) to select to 1" read depth detection.
The 1" mode LED will illuminate (illustration 2).
The unit will then calibrate, followed by a
beep and a green LED will illuminate.
3. Triple-click / Depress "ON" button three times
(3x) to select 1-1/2" mode LED will illuminate
(Illustration 2). The unit will then calibrate,
followed by a beep and a green LED with
illuminate.
IMPORTANT: Unit will automatically shut-off
if ON button is released following steps 1, 2,
3 above.
5.0 Calibration Precaution
Calibrate the unit on wall before scanning, for
wood or metal stud, or other objects.
Notes: While calibrating, the intelliSensor™
Pro METAL must not be placed directly over
a stud, dense material such as metal, wet or
newly painted areas as this will prevent the
unit from calibrating properly. If this is done
over wood or metal stud the unit will give no
indication when moved away from the area.
Move to a different location and try again.
5
Operating Instructions
Prepareing for use
1.0 Battery:
Open the battery door on
back of unit and connect a
9-volt battery (not included)
to clip. Place battery back
into case and snap battery
door on. Recommend to
r e p l a c e a n e w 9 v o l t
battery when low battery
indicator is on.
2.0 Selecting stud or metal scan mode:
NOTE: Select scanning mode prior to
pressing ON button
STUD SCAN: Depress STUD scan button
(Illustration 3) to detect wood and metal
studs. Stud mode does not differentiate
between wood and metal objects.
METAL SCAN: Depress METAL scan
button (Illustration 3) to detect the presence
of metal objects. This mode only detects
metal and will not detect the presence of
non-metal objects. Refer to the specification
section for scanning depth capability.

3.0 Turning Power ON

The ON/MODE Button is located on the right
side (Illustration 1) of the hand grip.
GB
6.0 Calibrating
Hold the IntelliSensor™ Pro METAL flat
against he surface, makeing firm contact.
P r e s s a n d h o l d t h e " O N " b u t t o n . A l l
indicators on the LCD are displayed while
the unit goes through its' 1 to 3 second
calibration cycle. The word "CALIBRATING"
will apear on LCD (illustration 2) while the
unit is cablibrating to surface. Following the
completion of calibration the unit will beep,
and the word "READY" will be shown on
LCD (illustration 5). The LED light will then
illuminate the keypad depth mode (1/2"
depth default).
IMPORTANT: The unit cannot be moved
before calibration is complete and "READY"
appears on the LCD.
IMPORTANT: The unit cannot be moved
before calibration is complete.
This sensor is designed for use only on
interior surfaces.
For best results the depth mode selected
should be based on the thickness of the
surface material being scanned (Reference 10)
GB
Battery Door
ILLUSTRATION 4
4
GB
READY
ILLUSTRATION 5
6
GB