Danfoss EKC 202D1 Mode D'emploi page 7

Transfer a set of pre-settings. o62 =
Function / Code
Normal operation
Temperature (set point)
Thermostat
Differential
Max. limitation of setpoint setting
Min. limitation of setpoint setting
Manual service, stop regulation, start regulation (-1, 0, 1)
Reference displacement during night operation
Value of reference displacement
Selection of thermostat sensor S4% during night opera-
tion with night blinds
Temperature difference for night blinds
Alarm
Delay for temperature alarm
Delay for temperature alarm after defrost
High alarm limit
Low alarm limit
Definition of alarm sensor
Signal for alarm thermostat. S4% (100%=S4, 0%=S3)
High alarm limit for S3
Low alarm limit for S3
Compressor
Reversed relay function for Compressor relay 1
(NC-function)
Defrost
Defrost stop temperature
Interval between defrost starts
Max. defrost duration
Drip off time
Delay for fan start after defrost
Fan cutin during defrost
Defrost sensor
Miscellaneous
Delay of output signal after start-up
Used sensor type (Pt /PTC/NTC)
Display step = 0.5 (normal 0.1 at Pt sensor)
Max hold time after coordinated defrost
Select signal for display view. S4% (100%=S4, 0%=S3)
Input signal on DI2. Function:
Rail heat during day operation
Rail heat during night operation
The buttons
Set menu
1. Push the upper button until a parameter
r01 is shown
2. Push the upper or the lower button and
find that parameter you want to change
3. Push the middle button until the
parameter value is shown
4. Push the upper or the lower button and
select the new value
5. Push the middle button again to enter
the value.
Cutout alarm relay / receipt alarm/see alarm
code
• Push short the upper button
EKC 202D1
1
--- -8.0°C
r01 4.0 K
r02 -5.0°C
r03 -10.0°C
r12 1
r13 0
r40 0
r61 0
r75 0
A03 30 min
A12 60 min
A13 13.0°C
A14 -8.0°C
A33 1
A36 0
A56 13.0°C
A57 -8.0°C
c30 0
d02 5.0°C
d03 12 hours 12 hours 48 hours 12 hours 24 hours 24 hours
d04 45 min
d06 0 min
d07 0 min
d09 Yes
d10 0
o01 5 s
o06 NTC
o15 Yes
o16 20 min
o17 0
o37 12
o41 100%
o42 100%
Set temperature
1. Push the middle button until the
temperature value is shown
2. Push the upper or the lower button and
select the new value
3. Push the middle button to select the
setting.
Reading the temperature at defrost sensor
• Push briefly the lower button
Manuel start or stop of a defrost
• Push the lower button for four seconds.
Instructions RI8NK459 © Danfoss 06/2015
2 3 4 5
-32.0°C -30.0°C -32.0°C -28.0°C
4.0 K 1.0 K 4.0 K 1.0 K
-28.0°C -28.0°C -28.0°C -25.0°C
-34.0°C -34.0°C -34.0°C -50.0°C
1 1 1 1
0 0 0 0
0 0 0 6 K
0 0 100% 0
0 0 0 0
30 min 30 min 30 min 10 min
60 min 60 min 60 min 35 min
-11.0°C -11.0°C -11.0°C -15.0°C
-32.0°C -32.0°C -35.0°C -50.0°C
1 1 1 2
0 0 100% 0
-11.0°C -11.0°C -11.0°C -16.0°C
-32.0°C -32.0°C -35.0°C -50.0°C
0 0 0 0
5.0°C 5.0°C 5.0°C 5.0°C
45 min 45 min 45 min 60 min
2 min 2 min 2 min 10 min
3 min 0 min 3 min 5 min
No Yes No No
0 0 0 0
5 s 5 s 5 s 5 s
NTC NTC NTC NTC
Yes Yes Yes Yes
20 min 25 min 25 min 15 min
0 0 100% 0
12 12 12 12
100% 100% 100% 100%
100% 100% 100% 100%
6 7 8 9
-28.0°C -2.0°C -1.5°C 0.5°C
1.0 K 1.0 K 1.0 K 1.0 K
-25.0°C 5.0°C 6.0°C 4.0°C
-50.0°C -10.0°C -2.0°C -1.0°C
1 1 1 1
0 0 3 K 3 K
0 0 -1.5 K 0.5 K
0 0 0 0
0 0 3 K 3 K
10 min 30 min 10 min 10 min
35 min 60 min 45 min 45 min
-15.0°C 10.0°C 2.0°C 5.0°C
-50.0°C -10.0°C -50.0°C -50.0°C
1 1 1 1
100% 0 100% 100%
-15.0°C 10.0°C 50.0°C 50.0°C
-50.0°C -10.0°C -50.0°C -50.0°C
0 0 1 1
15.0°C 7.0°C 10.0°C 10.0°C
6 hours 4 hours 4 hours
45 min 40 min 35 min 35 min
10 min 0 min 0 min 0 min
5 min 0 min 0 min 0 min
No Yes Yes Yes
0 0 S4 S4
5 s 5 s 0 0
NTC NTC NTC NTC
Yes Yes No No
15 min 20 min 30 min 30 min
100% 0 0 0
12 12 12 12
100% 100% 0 0
100% 100% 0 0
LED
Light emitting diode
= refrigeration
= defrost
= fan running
Flashes fast at alarm
10
-2.0°C
2.0 K
50.0°C
-50.0°C
0
0
0
100%
0
30 min
90 min
8.0°C
-30.0°C
1
100%
8.0°C
-30.0°C
0
6.0°C
8 hours
45 min
0 min
0 min
Yes
0
5s
Pt
No
20 min
100%
0
100%
100%
7