Silverline 684786 Mode D'emploi page 15

684786
Smart Jump Start Protector Unit (Fig. II)
Green and Red LED Status Condition Description
Solid Green LED Cable/clamp polarity correct,
the Lithium Jump Starter
voltage is above 11V, and
vehicle battery is above low
limit threshold
Green LED blinking and Vehicle battery is low
Smart Jump Start Protector
Unit beeping
Solid Red LED and Smart Connection is incorrect.
Jump Start Protector Unit Cable/clamps are in reverse
beeping polarity, a vehicle battery
short has been detected,
or incorrect Lithium Jump
Starter voltage
No LEDs or beeping Vehicle's battery may be
damaged
WARNING: If the Lithium Jump Starter becomes warm to the touch at any time, disconnect the
Lithium Jump Starter from the cables then allow to cool fully before re-attempting the next jump
start.
Maintenance
Note: The Lithium Jump Starter comes equipped with an internal rechargeable lithium polymer
battery. This battery is not consumer replaceable, and must be disposed of when the battery can no
longer hold charge. Correct charging practices will prolong the life of the battery.
• Charge the device fully at least once every 3–4 months if not used regularly to maintain the life
of the lithium polymer battery
Cleaning
• Keep your Lithium Jump Starter clean. Always clean dust/particles away
• Use a soft brush or dry cloth to clean the device
• Make sure that the positive and negative lead clamps are kept clean. Dirty electrical contacts will
severely impair the performance of this product
• A soft wire brush can be used to clean the clamps
• NEVER use water or alcohol-based cleaners to clean the device
Storage
• Store fully charged. The unit will hold charge for 6 to 12 months, but should always be charged
before the next use after being stored for a long period of time
• Store this tool carefully in a secure, cool, dry place (-10°–30°C / 14°–86°F) out of the reach of
children
• If storing in a moving vehicle, ensure that the unit, particularly the Lithium Polymer Battery Pack
(1), cannot move around freely
12V Lithium Jump Starter & Powerbank
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
Action
and are not viable for repair.
• Do not dispose of power tools or other waste electrical and electronic equipment (WEEE) with
Can now attempt to jump
household waste
start the vehicle
• Contact your local waste disposal authority for information on the correct way to dispose of power
tools
Troubleshooting
Press Jump Start Protector
Boost Button. Wait until
Green LED is solid then,
Problem
within 30 seconds, attempt
to jump start the vehicle
Lithium Jump Starter
will not switch OFF when
Do not attempt to jump start
pressing the Power
the vehicle. Disconnect High
Button (3)
Current Connector Plug and
remove clamps from the
vehicle's battery terminals.
The Lithium Jump Starter
Reconnect clamps to the
will not switch ON when
vehicle's battery in correct
pressing the Power Button
polarity (see ' J ump starting
a 12V vehicle') then connect
the High Current Connector
Plug to the Lithium Jump
Starter
Note: The source of this
problem must be found and
resolved before any more
attempts are made to jump
During charging, the
start the vehicle using the
Lithium Jump Starter
Lithium Jump Starter
stops charging and begins
beeping
Disconnect High Current
Connector Plug and remove
clamps from the vehicle's
battery terminals. Reconnect
in correct polarity to the
vehicle's battery terminals
and Lithium Jump Starter. If
there is no solid Green LED,
press the Boost Button.
The Lithium Polymer Battery
Pack becomes hot to touch
during use/begins to swell
Possible cause Solution
The automatic switch off Leave the device unplugged
from cables and all other
devices for approximately 10
seconds, and the unit should
switch off automatically
The Lithium Polymer Battery Charge the unit from a
Pack (1) has no charge power supply into the
Quick Charge Input Port
(4). If after charging the
device does not switch on,
it may have reached the
end of the battery life and
will need to be disposed
of in accordance with local
authorities (see 'Disposal')
There is a problem with 1. Press and hold the Power
the charging procedure; Button for 10–30 seconds
the Lithium Polymer to force the continuation
Battery Pack has detected of charging and possibly
a problem correct the charging issue
2. After pressing and
holding the Power Button,
disconnect the power supply
and allow the Lithium Jump
Starter to reset
3. Reconnect the power
supply to the Lithium Jump
Starter to see if the unit will
charge again normally
4. If the unit again
discontinues charging
and begins beeping,
IMMEDIATELY DISCONNECT
the power supply and
discontinue use. Consult
an authorised Silverline
technician
Note: After pressing and
holding the Power Button
during this process, the
LED Light (5) will come
on, which is normal. After
disconnecting the charger,
the LED Light may be turned
OFF (see 'Using the Torch/
Strobe/SOS LEDs') before
reconnecting the charger
The Lithium Polymer Battery IMMEDIATELY DISCONNECT
Pack is faulty the power supply/cables and
discontinue use. Consult
an authorised Silverline
technician
silverlinetools.com
15