Product Familiarisation - Silverline 684786 Mode D'emploi

684786
Jump Starter Safety
• Do not allow positive and negative lead clamps to make contact. Live clamps that come into
contact with each other could result in the leads melting, and/or create a fire hazard
• Do not attempt to jump start any vehicle whose battery is leaking, cracked, or otherwise damaged
• Do not attempt to jump start a vehicle with a frozen battery. Exercise caution when bringing such
a battery into a building as there is a possibility the battery could leak when it returns to normal
temperature
• Unless the battery in the vehicle is of the 'maintenance-free' type, always check that the
electrolyte level is correct before attempting to jump start the vehicle
• Lead-acid batteries emit explosive, flammable gases, particularly during attempts at starting a
vehicle. DO NOT SMOKE and do not expose the jump starter or vehicle's battery to any open flames
or high temperature surfaces. The lead acid battery in a vehicle is the primary concern for flammable
gas
• Only use in well-ventilated areas
• Always wear protective gloves and goggles when handling lead acid batteries
• Always remove all metal jewellery before handling lead acid batteries
• Be aware that loose clothing and long hair could get caught in moving engine parts. When using
this product, tie up hair and secure loose clothing
• Wash thoroughly with soap and water if battery acid contacts skin or clothing. If battery acid
contacts eyes, wash thoroughly with clean water and seek medical help
• Only use this jump starter in completely dry conditions
• If the Jump Starter becomes swollen during use or when charging, IMMEDIATELY DISCONNECT
Jump Starter from the cables or power supply and discontinue use
• If at any time the Jump Starter begins to swell, smoke, or become hot to the touch, IMMEDIATELY
DISCONNECT the Jump Starter and discontinue use
Lithium Polymer & Other Battery
Safety
WARNING: Lithium polymer batteries are volatile. If lithium polymer batteries are incorrectly
used, stored or charged they can become a fire, burn and/or explosion hazard.
• Keep the battery out of reach of children
• ONLY charge lithium polymer batteries using the charger provided or designed specifically for
your product
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow these
instructions may cause overheating or fire
• When not in use, batteries should be stored at room temperature (approximately 20°C)
• Ensure that battery contacts cannot accidentally short in storage. Keep batteries clean; foreign
objects or dirt may cause a short. Keep away from other metal objects, for example, paper clips,
coins, keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause skin
irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, seek medical help
• DO NOT open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in fire or
similar
• Never allow a metal tool to concurrently touch both the positive and negative cable/clamp ends
or battery terminals
• Be sure to have someone close by you when you are working with electricity and batteries,
particularly lead acid batteries
• If the vehicle battery needs to be removed, always remove the negative/black terminal first,
followed by the positive/red terminal. Ensure ALL vehicle electrical accessories are switched OFF
before removing the battery
• If working with lead acid batteries, ensure there is water, soap, and bicarbonate of soda readily
available, just in case there is any skin contact with battery aci
12V Lithium Jump Starter & Powerbank

Product Familiarisation

1. Lithium Polymer Battery Pack
2. LED Power Indicator Lights
3. Power Button
4. Quick Charge Input Port
5. LED Torch
6. USB Output 5V 2.1A
7. USB Quick Charge Output
8. Jump Starter Socket
9. High Current Connector Plug
10. Smart Jump Start Protector Unit
11. Black Negative Clamp
12. Red Positive Clamp
13. Red LED
14. Green LED
15. Jump Start Protector Boost Button
16. 3-in-1 USB Charging Cable
17. USB
18. USB Micro
19. USB C
20. Lightning Connector
21. Storage Case
Intended Use
Power bank used as a portable, high-current DC jump starter. Power bank is also capable of charging
or powering other portable devices via the USB Output 5V 2.1A and USB Quick Charge Output ports,
and has an LED torch light with flashing, safety modes, including SOS.
Unpacking Your Product
• Carefully unpack and inspect your new product. Familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
Charging the Jump Starter
IMPORTANT: The Jump Starter should be fully charged before initial use. Always charge the Jump
Starter on a hard surface away from combustible materials and do not leave unattended while
charging.
• Plug the USB Micro (18) into the Quick Charge Input Port (4) and the USB (17) into any USB
output port
• Ensure power supply from a USB output port is ON to charge the Lithium Jump Starter
Note: To check the charge state of the Lithium Jump Starter press the Power Button (3) and the LED
Power Indicator Lights (2) will illuminate. The number of illuminated LED lights indicates charge
level: 0=0%; 1=25%; 2=50%; 3=75%; 4=100%.
Note: When charging, the LED Power Indicator Lights will flash sequentially. As charging progresses,
the lights illuminate solidly without blinking. The more lights that are illuminated solidly, the higher
the charge level. The Lithium Jump Starter is fully charged (100%) when all LED Power Indicator
Lights are illuminated solidly without blinking.
silverlinetools.com
13