Maintenance / Service - Skil 1475 Notice Originale

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Changing accessories 7
! disconnect the plug
- remove/mount the required accessory as illustrated
- ensure that the openings of the accessory engage into
the tabs of the tool head (any snap-in position
possible)
- mount the accessory with the depressed centre
pointing downwards
- take hex key A from storage B 2
- loosen/fasten screw C with hex key A
- check the tight seating of the accessory (incorrect
or not securely fastened accessories can come loose
during operation and create a hazard)
• Mounting of sanding sheet 8
- tap the dust out of the VELCRO material on sanding
pad D before mounting the sanding sheet
- mount VELCRO sanding sheet E as illustrated
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot
! replace worn sanding sheets in time
! always use the tool with the total VELCRO
surface covered with sanding paper
• Mounting of auxiliary handle F 9 (1480)
! disconnect the plug
- screw auxiliary handle F on the right or the left of the
tool (depending on the work to be carried out)
• Dust suction 0
! disconnect the plug
- use dust extraction device G only when working with
sanding pad D
- mount dust extraction device G as illustrated
- connect vacuum cleaner
! do not use dust extraction device/vacuum cleaner
when sanding metal
- clean dust extraction device G regularly for optimal
dust pick-up performance
• On/off
- switch on/off the tool by pushing switch H 2 in "I"/"O"
position
! before the accessory reaches the workpiece, the
tool should run at full speed
! before switching off the tool, you should lift it
from the workpiece
• Adjusting working speed !
- with wheel J the required oscillating frequency can be
adjusted from low (1) to high (6) (also while tool is
running)
- the optimal working speed depends on the material
and can be determined with practical trials
• Holding and guiding the tool
! while working, always hold the tool at the
grey-coloured grip area(s) @
- keep ventilation slots K uncovered
- do not apply too much pressure on the tool (excessive
pressure will cause excessive heat and may shorten the
service life of the accessory)
• Depth adjustment accessory (DEPTH STOP) (not
standard included) #
APPLICATION ADVICE
• For optimal results on different materials use table $ as
reference for determining the right accessory (accessories
not standard included)
• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation slots
K 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in manufacturing
and testing procedures, repair should be carried out by an
after-sales service centre for SKIL power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law, electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 62841 the sound
pressure level of this tool is 83 dB(A) and the sound power
level 94 dB(A) (standard deviation: 3 dB), and the vibration
✱ (triax vector sum; uncertainty K = 1.5 m/s²)
✱ when sanding 6.2 m/s²
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when using
the tool for the applications mentioned
- using the tool for different applications, or with different or
poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns
12