Mono Sub With Active Satellites - Samson Audio RESOLV 120a Manuel Du Propriétaire

Mono Sub With Active Satellites

If you have active studio monitors, installation is easy through the RESOLV 120a's LINE LEVEL inputs and outputs. Below
is a typical system set-up using the RESOLV 120a with a mixer and a pair of active satellite speakers. The RESOLV 120a's
inputs and outputs utilize industry standard RCA connectors. For a detailed wiring diagram, see the section "RESOLV
120a Connections" on page 19. Follow the steps in the diagram below to set up your system.
FROM MIXER
• Lower your mixer's master outputs to all the way off.
• Connect the mixer's left output to the RESOLV 120a's LEFT LINE INPUT and the mixer's right output to the RESOLV
120a's RIGHT LINE INPUT. Now connect the RESOLV 120a's LEFT LINE OUTPUT to the input of the left powered satel-
lite, and the RESOLV 120a's RIGHT LINE OUTPUT to the input of the right powered satellite.
• Now adjust the SWEEP control to the desired frequency. Consult your studio monitors owner's manual for a recom-
mended crossover point. You can also use your ears by adjusting the SWEEP control to the frequency that sounds
good to you. A good place to start is about 70 Hz.
• Now set the level of your active satellite speakers up to the normal operating level. Run an audio signal (like some
music from a CD) through your mixer and raise the level to a comfortable listening level. Now slowly raise the
RESOLV 120a VOLUME control and listen to the low frequency output. Adjust the RESOLV 120a to the level of low fre-
quency output that you like. Now, when you raise and lower your mixer's output, the RESOLV 120a and satellites will
track at the same relative volume.
Connecting the RESOLV 120a
LOG FREQUENCY - Hz
5
0
-9
dBr dB 0.00
-15 15.0 0.79
10.0 1.63
5.0 2.43 mSec
-21
0.0 3.27
-27 -5.0 4.06
1K
10 100 10K 30K
CROSSOVER FREQUENCY (Hz) 100.0 1000.0 10000.0 SPECTRAL DECAY
50
30
+6
+3 0
dBr
0 -15
-3
-6 -30
500 1K 2K 5K
-50
10 100 1K 10K 30K
MID PRESENCE FREQUENCY (Hz) FREQUENCY RESPONSE FREQUENCY (Hz)
0dB +3dB
-3dB +6dB ACTIVE MONITOR
POWER
SPECS:
•20Hz - 20kHz
MID PRESENCE •BIAMPED 75 WATT WOOFER
COPOLYMEP CONE
ON
•25 WATT TITANIUM FERRO
AUDIO
FLUID TWEETER
INPUTS
•TIME ALIGNED WAVEGUIDE OFF
•MAGNETICALLY SHIELDED
WARNING:
RESOLV MONITORS CAN ACHIEVE
0 10 EXTREMELY HIGH SOUND PRESSURE
VOLUME
LEVELS. USE CAUTION OR HEARING
DAMAGE MAY RESULT
LINE
S/N
POWER 115-230 vac — 50Hz/60Hz 175W
RATING
CAUTION
BALANCED RISK OF ELECTRIC SHOCK
DO NOT OPEN
www.samsontech.com
DESIGNED AND ENGINEERED IN THE UNITED STATES BY SAMSON TECHNOLOGIES
MADE IN CHINA
5
0
-9
dBr
-15
-21
-27
10 100 1K 10K 30K
CROSSOVER FREQUENCY (Hz)
+6
+3
0
-3
-6
500 1K 2K
MID PRESENCE FREQUENCY (Hz)
0dB +3dB
-3dB +6dB ACTIVE MONITOR
SPECS:
•20Hz - 20kHz
MID PRESENCE •BIAMPED 75 WATT WOOFER
COPOLYMEP CONE
•25 WATT TITANIUM FERRO
AUDIO
FLUID TWEETER
INPUTS
•TIME ALIGNED WAVEGUIDE
•MAGNETICALLY SHIELDED
WARNING:
RESOLV MONITORS CAN ACHIEVE
0 10 EXTREMELY HIGH SOUND PRESSURE
VOLUME
LEVELS. USE CAUTION OR HEARING
DAMAGE MAY RESULT
LINE
S/N
POWER
RATING
BALANCED
www.samsontech.com
DESIGNED AND ENGINEERED IN THE UNITED STATES BY SAMSON TECHNOLOGIES
10 Inch Long Throw Transducer 120 Watt Amplifier
15
LOG FREQUENCY - Hz
dB 0.00
15.0 0.79
10.0 1.63
5.0 2.43 mSec
0.0 3.27
-5.0 4.06
100.0 1000.0 10000.0 SPECTRAL DECAY
50
30
0
dBr
-15
-30
5K
-50
10 100 1K 10K 30K
FREQUENCY RESPONSE FREQUENCY (Hz)
POWER
ON
OFF
115-230 vac — 50Hz/60Hz 175W
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
MADE IN CHINA