Driver Installation - Renkforce DU3900 Mode D'emploi

Driver installation

Do not connect the product to a computer while installing the driver.
• Install the CD in the corresponding drive of your computer. If installation does not start
automatically, open the following file on the CD: Setup.exe
• Follow the on-screen instructions.
• Restarting the operating system might be required after installation, in order for the product
to work properly.
Connection
• Connect the hollow plug from the power adapter to the power socket (5).
• Connect the power adapter to a common household wall socket.
• Connect the type B USB port (6) to a USB 3.0 port of your computer using the provided USB
cable.
• When using for the first time, the operating system will recognize a new hardware and then
complete the driver installation. This might take several minutes. The screen might flicker a
few times or turn black briefly during installation. That is normal when a new external graphic
card is recognized.
• The product is then ready for use.
Operation
a) Connecting a monitor
• Connect an HDMI monitor to the HDMI port (3).
• Connect a DVI monitor to the DVI port (2).
If having connected two monitors to the product, the maximum resolution for both
monitors accounts for 2048 x 1152 pixels each.
4K UHD playback via HDMI is only possible with the DVI port not being connected.
b) USB ports
• All 4 USB ports (7, 8) are suitable for connecting USB periphery devices (e.g. mouse,
keyboard, USB sticks, etc.).
• The ports are downwards compatible with USB 2.0/1.1. That allows you to also connect older
USB devices to these ports.
• The two USB charging ports (8) on the front are suitable, for example, for charging
smartphones/tablets. The maximum output current per port is 1.5 A.
The charging ports conform to BC 1.2 specifications.
c) Network port
• Connect the RJ45 port (4) to a router or network switch using a 1:1 connected, fully wired
network cable.
• If possible, have the connection and configuration carried out by a network or system
administrator (e.g. in larger companies).
• There are numerous reasons for network connections not being established properly. Refer
to corresponding expert literature or contact a specialist.
d) Connecting headphones/microphones
The jack socket (9) is intended for connecting headphones, headsets or microphones.
The jack socket is a combined socket functioning as both audio input and audio
output socket.
Tips and notes
• The CD includes the English operating instructions of the manufacturer.
• Never disconnect the product from the computer during use, in order to avoid data loss.
• Never operate the product without the provided mains adapter.
Cleaning and care
• Under no circumstances use aggressive cleanings agents, cleaning alcohol or other chemical
solutions since these can penetrate the housing or impair functionality.
• Disconnect the product from all connected devices before cleaning.
• Never submerge the product in water.
• Have maintenance and repairs done by qualified experts or repair shops only. There are
no components located inside the product you need to maintain. Never open/dismantle the
product.
• To clean the product, a dry, soft and clean cloth is sufficient. Do not apply too much pressure
to the housing as this may cause scratch marks.
• You can easily remove dust using a long-haired, soft and clean brush.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
a) Docking station
Operating voltage ......................... 5 V/DC
Connections .................................. 4 x USB 3.0,
1 x HDMI,
1 x DVI,
1 x Gigabit Ethernet (RJ45, 10/100/1000 BASE-T)
1 x 3.5 mm jack socket (stereo)
1 x USB type B
System requirements .................... Windows
Cable length ................................. 90 cm (USB)
Operating conditions ..................... 0 to +40 °C, 0 – 90 % RH
Storage conditions ....................... -20 to +70 °C, 0 – 90 % RH
Dimensions (L x W x H) ................ 94 x 95 x 44 mm
Weight .......................................... 540 g
b) Power adapter
Input voltage ................................. 100 – 240 V/AC, 50/60 Hz
Output voltage / current ................ 5 V/DC, 4 A
Cable length ................................. 150 cm
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
7 (SP1 or higher), 8.0, 8.1, 10 (all 32/64 bit)
®
*1460835_V2_0716_02_IPL_m_en