Safety Instructions - Conrad BaseTech 1462835 Mode D'emploi

Operating instructions
Sound-active wireless doorbell
Item no. 1462835
Intended use
This wireless doorbell set is equipped with acoustic and optical call signalling (flashlight). Due to the built-in
sound-active sensor on the converter, no further wiring is necessary. The converter is installed directly next
to the existing sound source (e.g. bell, intercom). When the bell is rung, the acoustic signal is converted into
a radio signal by the sound-active sensor and sent to the wireless doorbell. The wireless doorbell is powered
by 2 type C/baby batteries. To operate the converter you need 2 AA batteries.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms,
must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Wireless doorbell
• Converter
• 4 x screws
• 4 x dowels
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code above.
Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in the triangle is used to highlight important information
in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.

Safety instructions

Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• The whole product is not allowed to get damp or wet, never touch it with wet hands!
• Consult an expert when in doubt about the operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
b) Batteries
• Correct polarity must be observed while inserting the batteries.
• Batteries should be removed from the device if it is not used for a long period of time to
avoid damage through leaking. Leaking or damaged batteries might cause acid burns when
in contact with skin, therefore use suitable protective gloves to handle corrupted batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying around, as there
is a risk that children or pets may swallow them.
• All batteries should be replaced at the same time. Mixing old and new batteries in the device
can lead to battery leakage and device damage.
• Batteries must not be dismantled, short-circuited or thrown into fire. Never recharge non-
rechargeable batteries. There is a risk of explosion!
Operating elements
Wireless doorbell
1 Indicator light
2 Flashlight
3 Speaker
4 Mounting plate
5 Volume control
6 Slide switch for bell/
flashlight
7 LR button
8 Battery compartment
Converter
9
9 Indicator light
10 Sensor
11 Mounting plate
12 Sound button
13 Setting switch for the
sensor
14 Battery compartment
Insert/replace the batteries
a) Wireless doorbell
• Move the cover of the battery compartment in the direction indicated by the arrow by applying light
pressure, and remove it from the reverse of the wireless doorbell.
• Insert 2 new type C/baby batteries (not supplied) into the battery compartment (8). Observe the correct
polarity while doing so ("+" = positive; "-" = negative). When you insert the second battery two short beeps
are emitted.
• Reattach the battery compartment cover and lock the battery compartment. The cover must audibly lock
into place.
It is possible to use rechargeable batteries. Due to the lower operating voltage (rechargeable
battery = 1.2 V, battery = 1.5 V) and the low capacity, the operating life is however reduced.
• A change of battery is necessary if the indicator light (1) on the front of the wireless doorbell flashes red.
Note that the wireless doorbell will be reset if you change the batteries. You have to pair all converters
again with the wireless doorbell.
b) Converter
• Move the cover of the battery compartment in the direction indicated by the arrow by applying light
pressure, and remove it from the reverse of the converter.
• Insert 2 new type AA batteries (not supplied) into the battery compartment (14). Observe the correct
polarity while doing so ("+" = positive; "-" = negative).
• Reattach the battery compartment cover and lock the battery compartment. The cover must audibly lock
into place.
It is possible to use rechargeable batteries. Due to the lower operating voltage (rechargeable
battery = 1.2 V, battery = 1.5 V) and the low capacity, the operating life is however reduced.
A change of battery is necessary if the indicator light (1) on the front of the wireless doorbell
flashes red.
Note that the wireless doorbell will be reset if you change the batteries. You have to pair all
converters again with the wireless doorbell.
Operation
a) First time of use
• After inserting the batteries in the wireless doorbell and in the converter, the converter automatically sets
a frequency.
• This frequency will be transmitted to the wireless doorbell, which then emits an acoustic and/or optical
signal (flashlight); (see chapter "Settings, d) Flashlight").
b) Pair several converters with the wireless doorbell
You can pair a maximum of 4 converters with the wireless doorbell. Proceed as follows to pair the second
converter with the wireless doorbell:
• Open the battery compartment cover on the reverse of the wireless doorbell, by pushing it in the direction
indicated by the arrow by applying light pressure.
• Hold the LR button (7) for approx. 4 seconds. The indicator light (1) on the front of the wireless doorbell
turns orange.
• To pair the converter with the wireless doorbell, insert batteries into the converter.
• If you have already inserted the batteries, press the Sound button (12) or turn the setting switch (13).
• If the wireless signal is correctly received, the wireless doorbell emits an audible tone an acoustic and/or
optical signal (flashlight) via its speaker (3). This depends on the position of the switch (6); (see chapter
"Settings, d) Flashlight"). The indicator lights (1 and 9) also turn green. The pairing process has been
successfully completed.
• Proceed as described above to pair the third and fourth converter.
After pressing the LR button the converter has to be paired within 10 minutes. If several
converters are used you can set a different ring tone for each converter. By doing so you can tell
which converter sent the signal to the wireless doorbell by the sound it makes.
10
Sens
11
12
13
14