Troubleshooting; Specifi Cation - Onkyo SBX-300 Manuel D'instructions

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Troubleshooting

The unit does not work.
 Press Reset button which is placed inside
the Reset engraved thin hole on the bottom
of this unit using such as a slender rod.
 Unplug the Power Cord from the wall
outlet, wait 10 seconds or more, then
plug it in again.
 Press the INPUT button repeatedly to
switch LINE IN mode (the source indicator lit Green), and press and hold
the
(Repeat) button on the remote control during the power is ON.
The unit is suddenly powered off .
 The unit has an energy saving function. The unit automatically enters the
standby mode in the following situations.
– No sound output and without any operation for more than 10 minutes
in the iPod mode.
– No signal input for more than 10 minutes in the LINE IN mode.
In such cases, turn ON the unit again and play back the audio.
The power does not come on.
 Make sure the Power Cord is connected to the wall outlet fi rmly. (P.6)
The buttons on the unit do not function.
 Remove and reconnect the AC adapter and turn on the unit again. (P.6)
There is no sound output.
 Check if the volume of the iPod/external device connected to the unit is
set to the minimum.
 Make sure the sound is not muted. (P.8)
 Adjust the VOLUME +/− buttons on the remote control or unit. (P.7, 8)
There is no audio from iPod.
 Make sure the iPod is connected fi rmly. (P.8, 9)
iPod operation is not performed.
 Make sure the iPod is connected fi rmly. (P.8, 9)
 Restart the iPod.
The iPod cannot be charged.
 Make sure the iPod is connected fi rmly. (P.8, 9)
 Make sure the Power Cord is connected to the wall outlet fi rmly. (P.6)
The Docking Tray cannot be closed.
 Switch the SLIDE TO CLOSE to direction of arrow. (P.9)
The remote control does not function.
 Make sure the battery is inserted correctly. (P.6)
 Replace the battery in the remote control with a new one if it is weak. (P.6)
 Move closer to the unit when using the remote control. (P.5)
Reset button
Bottom of unit

Specifi cation

General
Rated output Power(FTC): (L,R) 20 watts minimum continuous power per
channel, 6 ohm loads, 2 channels driven at 1 kHz
with a maximum total harmonic distortion of 1 %
Power Supply:
AC 100 – 240 V, 50/60 Hz
Power Consumption:
27 W
No-sound Power
Consumption:
4.8 W
Stand-by Power
Consumption:
0.3 W
Dimensions (Approx.):
17
11
(450 mm (W) × 176 mm (H) × 131 mm (D))
Weight:
7.7 lbs. (3.5 Kg)
Analog Input:
LINE
Amplifi er
Total Harmonic
Distortion+N:
0.5 % (1 kHz 1 W)
Damping Factor:
15 (Front, 1 kHz, 8 Ω)
Input Sensitivity/
Impedance:
1000 mV / 47 kΩ (LINE)
Frequency Response:
40 Hz to 20 kHz/+3 dB, -3 dB
Tone Control Characteristies: +4 dB, 80 Hz (S. BASS 1)
+8 dB, 80 Hz (S. BASS 2)
Signal to Noise Ratio:
76 dB (LINE, IHF-A)
Speakers
Speaker Impedance:
6 Ω
Speaker Outputs:
Internal speaker 2 ch
Type:
Full-range Bass-Refl ex
Unit:
4
1
/
8
Design and specifi cations are subject to change without notice.
/
" (W) × 6
15
/
" (H) × 5
3
/
" (D)
16
16
16
" (10.5 cm) cone
11
En-

Publicité

Table des Matières
loading

Table des Matières