Ec Declaration Of Conformity - Chicago Pneumatic CP7500D Manuel De L'opérateur

EN
English
INSTRUCTION MANUAL
Air Supply Requirements
1. Supply tool with 90 psig (6.2 bar) of clean, dry air.
Higher pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose, and
fitting sizes shown in the diagram.
3/8" (10mm)
3/8" (10mm)
Lubrication
1. Motor - Use an air line lubricator with SAE #10 oil,
adjusted to two (2) drops per minute. If an air line
lubricator cannot be used, add air motor oil to the
inlet once a day.
2. Gears - Remove screw (Index no. 27). Use grease
gun C098689 with Mobilux EP-2 or equal grease.
Re-install screw (Index no. 27).
Maintenance
1. Disassemble and inspect air motor every three (3)
months if the tool is used every day. Replace
damaged or worn parts.
2. High wear parts are underlined in the parts list.
3. Recommended accessories:
8940162768
Grinding Wheel 60 Grit (set of 5)
8940162769
Grinding Wheel 80 Grit (set of 5)
8940162770
Grinding Wheel 120 Grit (set of 5)
8940164490
Cutting Wheel (set of 5)
Copyright 2007, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks,
model denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of
unauthorized parts is not covered by Warranty or Product Liability.
1/2" (12mm)
CA048362 (1/2")
3/8" (10mm)
90
0 130
3/8" (10mm)
3/8" (10mm)
CA048360 (1/2")
CA048361 (1/2")
Angle Grinder / Cut-off Tool

EC DECLARATION OF CONFORMITY

We, Chicago Pneumatic Tool Co. LLC, 13325
Carowinds Blvd., Charlotte, NC 28273 USA, declare
under our sole responsibility that the product to which
this declaration relates, is in conformity with the
requirements of the Council Directive of June 1998 on
the approximation of the laws of the Member States
relating to machinery (98/37/EC).
Machine Name CP7500D 2" Angle Grinder / Cut-off
Tool
Machine Type Power tool equipped with 3/8"-24
spindle for use with various grinding and cutting
wheels - No other use is permitted.
Serial No. Tools with No. 06001P or higher
Technical Data
2" (50.8 mm) Grinding or cutting wheel
Free Speed 22,000 RPM
Air pressure 90 psi (6.2 bar)
Harmonized Standards Applied EN792-7
National Standards Applied ISO 8662-4(Grinder),
ISO 8662-12(Cut-Off Tool), ISO 15744-2002
Name And Position Of Issuer Stéphane
Rakotoarivelo, General Manager
Signature Of Issuer
Date Of Issue October 15, 2007
Noise & Vibration Declaration*
Sound pressure level 79 dB(A) uncertainty 3 dB(A),
in accordance with ISO 15744-2002. For sound
power, add 11 dB(A).
For use as a Grinder
Vibration value 6.5 m/s , re. ISO 8662-4.
For use as a Cut-off Tool
Vibration value 5.35 m/s , re. ISO 8662-12.
* These declared values were obtained by laboratory type testing in
compliance with the stated standards and are not adequate for use in
risk assessments. Values measured in individual work places may be
higher than the declared values. The actual exposure values and risk of
harm experienced by an individual user are unique and depend upon
the way the user works, the workpiece and the workstation design, as
well as upon the exposure time and the physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the consequences of
using the declared values, instead of values reflecting the actual
exposure, in an individual risk assessment in a work place situation
over which we have no control.
CP7500D
2
2