Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TE-AC 36/6/8 Li OF Set Instructions D'origine

Use as a blow-out pistol
To use the tire pressure gauge as a blow-out
pistol you must fi rst unscrew and remove the
hose with the valve adapter for care tires. Now the
blow-out adapter (16) can be screwed to the tire
pressure gauge.
Range of applications:
For cleaning and blowing out hollow spaces or
hard-to-reach areas, as well as for cleaning soiled
equipment. The infi nitely variable trigger lever al-
lows an exact dosing of compressed air.
7.2 Instructions for the adapter set
For information on the correct use of the adapters
for the various valves, please refer to the following
overview (see Fig. 12 which shows how to con-
nect the adapter to the compressor).
•
Ball needle (Fig. 5)
Area of application: For inflating balls. The
ball needle can be used to inflate a variety of
different balls.
TIP: To avoid damaging the valve, moisten
the needle slightly before inserting it.
•
Valve adapter (Fig. 6)
Area of application: For Dunlop cycle tire
valves.
This Dunlop valve adapter is designed for
inflating cycle tires.
•
Adapter I (Fig. 7/Item I)
Area of application: For all valves with an in-
ternal diameter of 8 mm or more.
You can use this adapter to inflate airbeds,
pools or boats.
TIP: Insert the adapter I into the valve as
shown in Figure 7, drawing d.
Important! The valve cap must be opened a
little by being pressed together slightly.
•
Adapter II (Fig. 8/Item II)
Area of application: For screw valves.
This adapter can be used for all conventional
boats, kayaks and other large items such as
pools, which are fitted with a screw valve.
•
Vent adapter (Fig. 9/Item III)
Area of application: For deflation valves You
can find a deflation valve combined with other
valves (standard valve, screw valve, etc.)
on many large articles such as an inflatable
mattress.
•
Conical universal adapter (Fig. 10-11)
Area of application: The universal adapter can
be used for inflating airbeds and other similar
items.
Anl_TE_AC_36_6_8_Li_OF_SPK13.indb 19 Anl_TE_AC_36_6_8_Li_OF_SPK13.indb 19
GB
8. Cleaning, maintenance and
ordering of spare parts
Hazard!
Remove the rechargeable batteries before
doing any cleaning and maintenance work.
Warning!
Wait until the compressor has completely
cooled down. Risk of burns!
Warning!
Always depressurize the tank before carrying
out any cleaning and maintenance work.
Warning!
After use, always switch off the equipment
immediately and pull out the rechargeable
batteries.
8.1 Cleaning
•
Keep the safety devices free of dirt and dust
as far as possible. Wipe the equipment with a
clean cloth or blow it with compressed air at
low pressure.
•
We recommend that you clean the appliance
immediately after you use it.
•
Clean the appliance regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be
aggressive to the plastic parts in the appli-
ance. Ensure that no water can get into the
interior of the appliance.
•
You must disconnect the hose and any
spraying tools from the compressor before
cleaning. Do not clean the compressor with
water, solvents or the like.
8.2 Condensed water (Fig. 1)
Important! To ensure a long service life of the
pressure vessel (2), drain off the condensed wa-
ter by opening the drainage cock (11) each time
after using.
Check the pressure vessel for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure
vessel. If you discover any damage, please con-
tact the customer service workshop.
- 19 -
19.04.2022 08:43:55 19.04.2022 08:43:55