Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Translation of the original instructions
CAUTION
reduce the risk associated with environmental contamination:
•
Do not throw electric power tools into the household waste! In accordance with the European Directive 2002/96/
CE on Waste Electrical and Electronic Equipment and transposition into national law, used electric power tools
must be collected separately and recycled in an environmentally friendly manner.
•
Separate collection of used products and packaging allows materials to be recycled. Use of recycled materials
helps prevent environmental pollution and reduces the demand for raw materials.
•
Dispose of all the process dust in accordance with all applicable regulations.
To reduce the risks associated with fly off of abrasive product or parts:
•
Use care in attaching abrasive product and disc pad; following the instructions to ensure that they are securely
attached to the tool before use.
•
Never free spin the tool or otherwise allow it to be started unintentionally.
•
Never point this product in the direction of yourself or another person, or start tool unintentionally.
•
Never over-tighten accessory fasteners.
Specification:
Model No.
ELSN-B50H(V)-2.5
ELSN-B50H(V)
ELSN-B60H(V)-2.5
ELSN-B60H(V)
ELSN-B50H(V)-2.5-4
ELSN-B50H(V)-4
ELSN-B60H(V)-2.5-4
ELSN-B60H(V)-4
ELSC-B50H(V)(HM)-2.5
ELSC-B50H(V)(HM)
ELSC-B60H(V)(HM)-2.5
ELSC-B60H(V)(HM)
ELSC-B50H(V)(HM)-2.5-4
ELSC-B50H(V)(HM)-4
ELSC-B60H(V)(HM)-2.5-4
ELSC-B60H(V)(HM)-4
OPERATING INSTRUCTIONS
Prior to the operation
The tool is intended to be operated as a hand held tool. It is always recommended that while using the tool, operators
stand on a solid floor, in a secure position with a firm grip and footing. Be aware that the sander can develop a torque
reaction.
Starting and stopping sander
1. Plug-in the sander's AC power cord to the power source (220VAC output). The warning " beep " sounds would be
occurred after the plug is securely plug-in to the power source and the LED indicator shows " Solid Red " color at
the moment.- see figure 1.
2. Press the power on/off button " ϴ " on the button plate to switch on the sander. The LED indicator shows " flash
green " color after sander being switched on. - see figure 2.
3. Adjust the speed by pressing " + " or " – " buttons on the button plate. Press " + " is to raise up to higher speed
setting, " – " is to lower the speed setting. - see figure 3.
4. Press the lever to start running the tool. Release the Lever to stop the tool.
ELECTRIC DUAL ACTION (DA) SANDER
Orbit
Pad Size
Sander
Type
inch mm inch mm (r.p.m.)
3/32
2.5
5
3/16
5
5
Non
Vacuum
3/32
2.5
6
3/16
5
6
3/32
2.5
5
3/16
5
5
Non
Vacuum
3/32
2.5
6
3/16
5
6
3/32
2.5
5
3/16
5
5
Central
Vacuum
3/32
2.5
6
3/16
5
6
3/32
2.5
5
3/16
5
5
Central
Vacuum
3/32
2.5
6
3/16
5
6
Free
Motor Hp
Speed
(W)
127
127
152
152
127
127
152
4,000
152
7,000
350W Max
9,000
150W Rated
127
10,000
127
152
152
127
127
152
152
Length
Versions of
Volatge AC-in
inch mm lbs kgs
10.9 278 2.4 1.08
10.9 278 2.4 1.08
11.9 303 2.6 1.21
11.9 303 2.6 1.21
10.9 278 2.4 1.08
10.9 278 2.4 1.08
11.9 303 2.6 1.21
11.9 303 2.6 1.21
110VAC x 60Hz
220VAC x 50Hz
10.9 278 2.4 1.08
10.9 278 2.4 1.08
11.9 303 2.6 1.21
11.9 303 2.6 1.21
10.9 278 2.4 1.08
10.9 278 2.4 1.08
11.9 303 2.6 1.21
11.9 303 2.6 1.21
EN
Weight
9
Publicité
Table des Matières
