EINHELL TE-CD 18/45 3X-Li Instructions D'origine page 20

switch, the higher the speed of the battery-powe-
red drill/screwdriver.
6.6 Changing over from 1st gear to 2nd gear
(Fig. 4/Item 7)
You can work at a higher or lower speed depen-
ding on the position of the selector switch. To avo-
id damaging the gear unit you should only change
over gears when the tool has stopped.
6.7 Battery capacity indicator (Fig. 6 / Item 2)
Press the battery capacity indicator switch (a).
The battery capacity indicator (2) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6.8 LED lamp (Fig. 6/Item 10)
The LED lamp (10) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED lamp (10) will be lit
automatically as soon as you press the ON/OFF
switch (4).
6.9 Changing the tool (Fig. 7)
Important. Set the changeover switch (3) to its
centre position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
•
The cordless screwdriver is fitted with a
quick-action chuck (9) with an automatic
spindle stop.
•
Open the chuck (9). The chuck opening (a)
must be large enough to hold the tool (drill bit
or screwdriver bit).
•
Select the suitable tool. Push the tool as far
as possible into the chuck opening (a).
•
Tighten the chuck (9) and then check that the
tool is secure.
Anl_TE_CD_18-45_3X-Li_SPK13.indb 20
GB
6.10 Screwdriving
We recommend using self-centering screws (e.g.
recessed head screws) designed for reliable wor-
king. Be sure to use a bit that matches the screw
in shape and size. Set the torque, as described
elsewhere in these operating instructions, to suit
the size of screw.
6.11 Integrated magnetic bit mount
(Fig. 8-9/Item 11)
The cordless drill/screwdriver has an integrated
magnetic bit mount (11) for ¼ inch (6.35mm) bit
inserts.
To use it, remove the quick-change drill chuck (9)
by pressing the rear drill chuck sleeve (b) towards
the quick-change drill chuck.
You can now plug a suitable bit insert into the in-
tegrated magnetic bit mount (11).
To fi t the quick-change drill chuck (9) again, slide
it onto the bit mount (11) as far as it will go while
pressing the drill chuck sleeve (b). Then release
the drill chuck sleeve. The quick-change drill
chuck will lock automatically. Check whether the
quick-change drill chuck is secure.
6.12 Fitting the attachments
(Fig. 10-13 / Item 12+13)
The attachments (12+13) can be used to enable
screws to be screwed in and out and tightened in
hard-to-reach places.
The attachments (12+13) are fi tted in the same
way as the quick-change chuck (9). Pull back the
rear drill chuck sleeve (c/d) and fi t the attachment
onto the tool chuck of the equipment.
The attachments will lock automatically. Check
that the attachments are secure.
If the attachment does not lock automatically, turn
the hexagon chuck (Fig. 12/Item e/f) a little until
the rear drill chuck sleeve locks (Fig. 13).
You can now plug a suitable bit insert into the bit
mount.
To dismantle, proceed in reverse order.
6.13 Turning attachments
Remove the attachment, as described in 6.12,
and then fi t it back on again in the desired positi-
on. Check that the attachment is secure.
- 20 -
23.08.2021 08:49:25