Package Contents; Safety Instructions - Reely RE-5631027 Mode D'emploi

Operating Instructions
Professional 4-channel lighting system
Item no.: 1877009
Intended Use
The product is used as effect lighting for model vehicles and is designed for a 1:10 frame size. The LED
lighting is individually programmable in many functions and is delivered ready to connect. In addition, you
can use a programmable undervoltage detection for the drive battery. The connection cables of the individual
LED pairs are equipped with connectors protected against polarity. The LEDs are powered by the receiver
power supply (BEC or receiver battery).
For safety and compliance reasons, the product must not be converted or modified in any way. If you use the
product for other purposes than those described above, the product may be damaged. Furthermore, improp-
er use can cause risks such as short-circuits, fire, etc. Please read the operating instructions carefully and do
not discard them. Please include these operating instructions when you pass the product on to a third party.
This product complies with the applicable national and European Regulations. All names of companies and
products are the trademarks of the respective owners. All rights reserved.

Package contents

• 2x cables with 2 orange 3 mm LEDs • 1x connection cable with 2S balancer connection socket
• 2x cables with 2 white 3 mm LEDs • 1x buzzer
• 3x cables with 2 white 5 mm LEDs • Connecting cable for connection modules
• 1x cable with 2 red 5 mm LEDs • Adhesive pads, cable ties
• LED connection module • Operating instructions
• Servo connection module
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code
shown here. Follow the instructions on the website.
Meaning of the symbols
An exclamation mark in a triangle indicates important instructions in these operating instructions
that must be adhered to.
The arrow symbol indicates specific tips and advice on operation.

Safety Instructions

The warranty will be void in the event of damage caused by failure to observe these safety
instructions! We do not assume any liability for any resulting damage!
We shall not accept liability for damage to property or personal injury caused by incorrect
handling or non-compliance with the safety instructions! The warranty/guarantee will be
void in such cases.
• For safety and licensing reasons, unauthorised conversion and/or modifications to the product
are not permitted.
• The product must not get damp or wet. Risk of a short! The warranty will be void!
• The product is not a toy and should be kept out of the reach of children.
• The LEDs are only suitable for direct connection to the LED system. If other wiring is used, the
LEDs will be destroyed. The warranty/guarantee will be void!
• Warning! LED lights: Do not look straight into the LED light and don't use optical instruments
to do this!
• When installing the LEDs and the connection cables, make sure that cables/LEDs don't touch
moving/rotating drive parts and/or wheels.
• Handle the product with care; it can be damaged by impacts, blows or falls even from a low
height.
• Do not leave the packaging material lying around carelessly, since it could become a danger-
ous toy for children.
• Should you have questions that are not answered in these operating instructions, please
contact us or another expert.
• Maintenance, adjustment and repair work should only be carried out by an expert or a spe-
cialised workshop.
Installing the LED lighting system
Every model has its own construction and design; thus we can only provide general information
for the installation of the lighting system. For best light effects and because this LED system of-
fers many possibilities of individual design, we recommend to carry out a temporary installation
before a fixed installation.
Use appropriate tools (such as cable ties, adhesive pads) to attach the connection cables and LEDs to the
chassis or body. For the LEDs you need to drill appropriate holes at the corresponding locations.
Place the LEDs and the connection cables in such a way that they don't interfere with moving/rotating drive
parts and/or wheels. The chassis' moving parts should not chafe against the cables (for example when the
wheels deflect/bounce back or when steering).
It is good practice to attach the connection module to the inside of the top, using for example a double-sided
adhesive pad and to route all LED cables there. During installation, make sure that you can press the SET
button on the servo connection module for programming.
Locations for LEDs:
2x orange LEDs 3 mm: Turn indicator/winker
3x white LEDs 5 mm: Front mounted
2x white LEDs 3 mm: Can be installed anywhere; in the front, for example.
2X red LEDs 5 mm: Rear mounted
The table in the chapter "Startup" describes the LED functions .
Connecting the LED lighting system
The LEDs are only suitable for direct connection to the LED system. Connection module and LEDs are
powered by the receiver power supply (BEC of the cruise control or a receiver battery). If other wiring is used,
the LEDs will be destroyed. The warranty will be void!
The LED system is programmable. This partly allows for the functions of the LED outputs to
be changed. For initial start, we therefore recommend that you connect the LEDs in the basic
configuration before programming as described in this chapter and familiarise yourself with the
product in the preprogrammed factory settings.
If the control function of the remote control (left/right) does not match the LEDs and their in-
tended light function (e.g. when steering to the left, the right orange LEDs flash), swap the
slots of these LEDs accordingly or keep this in mind when installing the LEDs. For channels
CH2 (forward/reverse) and CH4 (switching channel for light control), the LED system allows for
reversing the polarity of the mode of operation in the LED system, which is independent of the
settings on the transmitter.
Plug the installed connectors of the LED lighting connection cables into the respective connector sockets of
the LED system provided for each LED. It is important to consider the shape of the jacks. The connectors
can only connect in one direction to prevent polarity reversal of the LEDs.
Fixed slots for individual LED pairs in basic configuration:
• Winker left (orange LEDs): L
• Winker right (orange LEDs): R
• Rear or brake light (red LEDs): BR1
• Reverse light (white LEDs when revers-
ing): REV
The function of the LED connections for indicators as well as the brake and reverse lights is
always available, regardless of the LEDs of other LED connections (e.g. white LEDs as driving
light on AUX1).
Freely selectable slots for individual LED pairs in basic configuration:
The LED connections AUX1, AUX2, FR1, FR2, FOG and ROF can be connected to the LED
pairs as desired. Activation of the LED connections is done in the basic configuration by operat-
ing channel 4 (CH4) on your remote control transmitter in the order shown below. There are four
switching states that repeat in an infinite loop.
The first stage switches on the LEDs of connections BR1 (as tail light function), ROF, AUX1 and AUX2 (which
can be used eg. as headlights).
The second stage switches on the LEDs of terminals FR1 and FR2 in addition to stage 1 LEDs.
In the third stage, the connection FOG is also switched on for all already activated LED connections.
If you press the CH4 switch on the transmitter once more (fourth stage), all connections shown in this section
are switched off again.
Connecting the servo connection module
Connect the servo connection module (1) to the receiver of your model (2). The cables with servo plugs
(CH1 - CH4) connect to the receiver at the respective connections:
• CH1: To the slot for the steering
• CH2: To the slot for the speed controller
• CH3: To switch channel 3 of the receiver
• CH4: To switch channel 4 of the receiver
The speed controller (3) must be plugged into the servo connection module on the open, upper contact pins
(see also ESC TH on the side). The steering servo (4) is connected to the lower plug contacts Servo ST.
Pay attention to the correct polarity (also see imprint). The negative pole of the servo plug
(brown or black cable) must face outwards.
To the left of the steering servo and speed controller pins there is a socket (5) for monitoring the voltage of the
drive battery. If you connect the supplied cable to the balancer socket here, you can monitor the voltage of an
attached battery. The connection cable is designed for a 2S battery and XH balancer connector.
If you have other balancer plugs on your batteries and/or use a 3S rechargeable battery, you need to build
your own suitable adapter (matching accessories can be found on our website www.conrad.com). Always
ensure the correct polarity.
Further information about the voltage control of the drive battery can be found in the next chap-
ter.
Finally, you must connect the 8-pin connection cable from the delivered items into the socket (6). Plug the
other end of the cable into the socket on the LED connection module. It is important to consider the shape of
the jacks. The connectors can only connect in one direction to prevent polarity reversal of the LEDs.
You will find the SET button at pos. 7. This button is used for programming - see the next chapters.