Time Settings - Aiwa TS-990 CD Mode D'emploi

12
en

TIME SETTINGS

SETTING THE CURRENT TIME
1. While the speaker is in standby mode, press
the TIME/PROG. button. The hour digits
on the display will blink.
2. Press the or buttons to select the
"24H" or "12H" format and press to
confirm the selection.
3. Press the or buttons to set the hour
and press to confirm. The minutes
digits on the display will blink.
Press or to set the minutes, press
4.
to confirm.
SETTING THE ALARM
This unit may be used as an alarm clock. The
CD/USB/card or FM radio are activated to
play at a preset time.
1. Press to switch the unit to standby mode.
Make sure that you have set the clock
2.
correctly.
3. Press the ALARM button in shutdown state.
4. Press or repeatedly to set the hour.
Press to confirm.
Press or to set the minutes. Press
5.
to confirm.
6. Press or to select the alarm volume
from 0 to 30. Press to confirm.
Press or to scroll through OFF-CD-
7.
USB-CARD-RADIO status. Press to
save the alarm.
8. The display will show the current time.
SNOOZE PERIOD
1. Whenever the alarm rings, it can be
temporarily suspended for a short period
of approximately 9 minutes, by pressing
once the ZZZ key on the remote control,
or the button on the top panel.
2. The alarm will then automatically begin to
ring again after approximately 9 minutes.
To deactivate the snooze, press and
3.
release the button once.
FM RADIO
You can store up to 30 of your favourite stations
in the tuner memory for easy recall at any time.
AUTO SCAN
1. Press the SOURCE key to select "RAD"
radio mode.
2. Long press the button, and your
speaker will scan and stop automatically
when it finds a station with sufficient
signal strength.
3. After a few seconds, the display will update.
The display will show the station frequency.
4. Press MEM+ or MEM- on the remote control,
or briefly press / on the top panel to
view and listen to the preset radio stations.
To find other stations, press and hold for
5.
2 seconds the button.
6. To scan the FM band in the oposite direction
(high frequencies to low frequencies),
press the button and hold for 2 seconds.
MANUAL SCAN
"RAD"
1. Press the SOURCE key to select
radio mode.
Press or to tune to a station. Each
2.
press on the tuning button will change
the frequency up or down by 100 kHz.
3. Once you find a station you want to save,
press and hold the MEM button on the
remote control or TIME/PROG on the top
panel. "S 01" will be shown on the display;
press MEM+ or MEM- until the desired
memory position number appears on the
display. Press the MEM or TIME/PROG again
to confirm and save the current station.
4. Briefly press MEM on the remote control;
or press TIME/PROG on the top panel,
"S 01" will be shown on the display; then
press MEM+ or MEM-, in order to view or
listen to the stored radio stations.
BASIC OPERATION CD / MP3
You can play in your tower speaker your
audio CD/ CD-R/ CD-RW/ MP3.
1. Press the button to turn on the unit.
2. Press the SOURCE button repeatedly to
select the CD function.
Press the button to open the disc tray.
3.
4. Insert a CD with the printing side facing
up and close gently the disc tray by
pressing again. The disc will start the
playback automatically.
To temporarily stop playback, press the
5.
button, and to resume playback, press
.
it again
6. Press the button to stop playback.
SEARCHING FOR A SECTION WITHIN A TRACK
During playback, press and hold or
buttons to find a specific passage within
the track and release it at the point you
want to listen to.
SELECT ANOTHER TRACK OR FILE
Press or buttons to skip to a different
track number.
Press once to hear the beginning of
the current track, and press it two or more
times to hear the previous track.
LISTENING TO YOUR TRACKS REPEATEDLY
Press the ALARM/REPEAT on the top panel
of the unit, or REP on the remote control
repeatedly to activate the repeat function
in following manner:
1. ONE (repeat the current track)
ALL (repeat all the available tracks)
2.
3. OFF (cancel the repeat function)
CREATING A CD PLAYLIST
The Program feature may be used to program
up to 33 tracks for CD and 99 tracks for
CD-MP3 to play in a selected order.
1. While in stop mode only (CD is not playing),
press and hold TIME/PROG on the top
panel of the unit, or the PRG button on the
remote control for 2 seconds, and the LED
display will show the wording "P 01" and
"T 01" starts to flash.
2. Press the and buttons to allocate the
desired track.
3. Press TIME/PROG or PRG to select and
store the track into the memory.
4. Repeat steps 2 and 3 to select up to 33/99
tracks.
To play the selected tracks (in the program
5.
mode), press the button.
6. Press the button to hear the previous
programmed track or press the button
to hear the next programmed track.
To clear the programmed tracks from the
7.
memory press the button twice.
ABOUT MP3 DISC COMPATIBILITY
With this unit is limited as follows:
Sampling Frequency: 32-48 (MP3)
Bit rate: 32-320kbps (MP3)
Do not use special letters such as:
/ :*?< > etc
Even if the total number of files on
the disc is more than 1000, it will only
show up to 999.
Note:
• Because MP3 discs have a large capacity,
disc access times are a little longer.
13