RIBELLE SpeedFun Mode D'emploi page 6

7.0 TORQUE LEVEL SETTING (only for Ribelle PLUS VERSION)
It is possible to choose one of the three settings proposed by speedfun which allow to obtain sometimes very important optimizations
on the engine response. The type of setting responds differently from bike to bike depending on the mode of use and the software
version of the motor and battery inserted in the ebike itself: in certain ebikes, better results are obtained with one level rather than
another, and in some ebikes the result is not very appreciable.
From assistance mode OFF press the key sequence: walk, minus, walk, minus, minus, walk, with the plus/minus keys select the
desired torque level (from 1-3) and press walk to save. The default level is nr. 1.
If you are unable to enter and modify this parameter, it means that your Ribelle is not of the PLUS version.
8.0 SPEED LIMITATION (only for Ribelle PLUS VERSION)
It is possible to set the maximum speed limitation value in steps of 5 kmH, upon reaching which the motor assistance will cut off or, by
setting it to 99, the maximum speed will be unlimited.
From assistance mode OFF press the key sequence: walk, minus, walk, minus, minus, minus, walk, , with the plus/minus keys set
the desired maximum speed and press walk to save.
If you are unable to enter and modify this parameter, it means that your Ribelle is not of the PLUS version.
The default setting is 99 (maximum speed without limit).
9.0 STATUS PASSWORD (only for Rebel PLUS VERSION)
It is possible to activate the password request to discourage theft. Each time the ebike is turned on, a 15 "countdown will start during
which you can enter the 5-letter password; if the password is not entered or entered incorrectly, the bicycle will switch off. The unique
password is printed on a white label attached to the rebel harness; it is made up of 3 letters which correspond to 3 keys: W = Walk,
P = Plus, M = Minus.
From assistance mode OFF press the key sequence: walk, minus, walk, minus, minus, minus, minus, walk, with the plus/minus
keys move to 55 ENABLED or 44 DISABLED, press walk to save. If you pass from Disabled to Enabled, you must enter the
password with a timeout of 15 " to save the setting.
If you are unable to enter and modify this parameter, it means that your Ribelle is not of the PLUS version.
The default setting is Disabled.
10.0 LEARNING OF THE WHEEL CIRCUMFERENCE INSERTED IN THE MOTOR.
To make Ribelle learn the circumference inserted in the motor, proceed as follows:
From assistance mode OFF and speed release DISABLED type the key sequence: walk, minus, walk, minus, minus, minus,
minus, minus, minus, walk, the display shows the figure 1.0, get on the ebike and travel one km approximately after which the digit
0.0 will be indicated to indicate it is necessary to stop. Once the measurement is complete, the display will show the number 33.0.
If the speed release is not deactivated, the display will show 0.0 to indicate that it does not accept the procedure.
11.0 TRIP COUNTER DISPLAY AND RESET
Ribelle is equipped with its own resettable distance counter (trip) that stores distances up to 99.9 km. When the maximum limit is
reached, the counter resumes counting from 0.
To view the counter, enter the following sequence from assistance mode OFF: walk, minus, walk, minus, minus, minus, minus,
minus, minus, minus, walk.. To reset the counter, press walk once again during the display.
12.0 VIEWING AND RESET AVERAGE SPEED
Ribelle is equipped with its own average speed calculator (avg) which works by excluding breaks and stops from the calculations.
To view the calculator, enter the following sequence from assistance mode OFF: walk, minus, walk, minus, minus, minus, minus,
minus, minus, minus, minus, walk. To reset the counter, press walk once again during the display
13.0 DISPLAY AND RESET MAXIMUM SPEED
Ribelle is equipped with a memory system for the maximum speed reached (max speed).
To display the maximum speed, the following sequence must be entered from assistance mode OFF: walk, minus, walk, minus,
minus, minus, minus, minus, minus, minus, minus, minus, walk. To reset the counter, press walk once again during the display
14.0 DIAGNOSTIC MODE
To connect the Bosch diagnosis to the ebike, Ribelle must be set in DIAGNOSIS mode so that it is completely transparent and not
detected.
To set Rebel in Diagnosis mode, the following sequence must be entered from assistance mode OFF: walk, minus, walk, minus,
minus, minus, minus, minus, minus, minus, minus, minus, minus, (menu 6.0) walk. The number 66.6 appears on the display to
indicate that the Diagnosis mode has been activated.
To exit the diagnosis mode, press the key sequence: walk, minus, walk, minus, minus, minus, minus, minus, minus.
Wait for the Ribelle software version to appear to indicate that you have exited the Diagnosis mode.
Pagina 6/14