Modes Of Operation - Bionaire BFH001X Manuel D'utilisation

WALL MOUNTING (Fig. 2, 3 and 4)
Your heater comes with a wall mounting bracket
allows you to mount the heater onto a wall.
If this heater is going to be used in a bathroom, or similar
room, it must be installed:
• In such a way that the switches and other controls
cannot be touched by the person in the bath or shower.
• Outside the grey shaded areas shown in Fig. 4.
If you are unsure about the installation of this heater in
the bathroom we recommend that you seek advice from a
professional electrician/installer.
Always refer to the specific regulations for the country of use
for information on where to locate the heater.
Due to the many different types of mounting surface,
mounting screws and fixings are not included with this
product.
1. Use the bracket as a template to mark the position of
the holes to be drilled.
Ensure that the position you choose is suitable for
mounting and supporting the heater and that the area
for fixing is away from any hidden electrical cables or
pipes.
2. Drill the holes and fix the bracket to the wall using
appropriate hardware.
3. Turn heater sideways and position the mounting tab on
the back of the heater so it lines up with the mounting
bracket (fig. 3).
4. Place mounting tab into the mounting bracket and
rotate heater into the upright position to lock it in place.
OPERATING INSTRUCTIONS
Place your heater on a firm level surface.
Plug your heater into a wall socket. Once plugged in the
LCD display will flash and show AM 12:00.
Setting the Clock
Your heater can be operated normally without setting the
clock but to program the heater to turn on at a preset time,
you must first set the clock.
1. Press and hold the set clock button
2. The hour digits on LCD display will flash. Turn the
control wheel to select 1 to 12, AM or PM.
E
3. Press the set clock button again until the minute digits
flash. Turn the control wheel to select the minutes.
4. Press the set clock button again to store the time.
On/Off Button
Press the on/off button
D
on/off button again to turn your heater off. Your heater will
cool down for 10 seconds, and then turn off. Your heater has
a memory and will remember the last temperature or mode
setting before your heater was turned off. However, if your
heater is unplugged, any settings will be lost.

MODES OF OPERATION

The mode button selects thermostat mode, fan only
C
mode, stay on mode or anti-frost mode.
which
I
for 3 seconds.
G
to turn your heater on. Press the
Thermostat Mode
Thermostat mode allows you to set your heater to a
precise comfort level. Press the mode button
thermostat icon ( ) appears on the LCD display. Turn the
control wheel to select the desired temperature (18°C
E
to 29°C)
The LCD display will show the selected temperature. When
the room temperature drops below the preset temperature,
the heater will automatically turn on again to maintain the
preset temperature level.
NOTES: It is normal for your heater to cycle on and off
to maintain the preset temperature. Raise the thermostat
setting to prevent your heater from cycling too frequently.
Whenever the preset temperature is reached or when your
heater is switched off, the fan will run for 10 seconds without
heat. This cool down process ensures an accurate and
consistent temperature reading.
Fan Only Mode
Fan only mode operates your heater without any heat
output. The fan icon (
Stay On Mode
The stay on mode will operate your heater continuously at
its maximum heat output. The "Stay On" icon will appear
on the LCD display. To turn your heater off, press the on/off
button .
D
Anti Frost Mode
Your heater is equipped with an anti frost feature. Your
heater will automatically turn on when the room temperature
drops below 5°C. To activate the frost guard feature, press
the mode button until the LCD display shows AF.
C
TIMER
The built-in timer can be set to turn your heater on at a
specified time.
Notes
• When in timer mode, your fan will always come on
in the "Stay On" mode. It will run for 30 minutes and
then automatically turn off. When the timer is operating
you cannot make any changes to the operating mode
without first powering the unit off.
• You must reprogram the timer feature each time you
want it to run.
1. To set the preset time press and hold the timer button
for 3 seconds.
H
2. The hour digits on LCD display will flash. Turn the
control wheel to select 1 to 12, AM or PM.
E
3. Press the timer button until the minute digits flash. Turn
the control wheel to select the minutes.
4. Press the timer button to activate the timer feature. The
timer icon ( ) and the current clock time will appear
on the LCD Display to confirm that the timer feature is
activated.
5. To turn off the timer feature, press and hold the timer
button for 3 seconds. The timer icon ( ) will go out.
5
until the
C
) will appear on the LCD display.