Selecting Power Up Test Option - "Put; Selecting Display Option - "Dsp; Selecting Buzzer Option - "Buz; Selecting Alarm Relay Setting - "Ars - Macurco CD-6H Instructions D'utilisation

3.5.2 Selecting Power Up Test Option – "PUt"
To select the Power Up Test Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then
push the Enter button to enter the Con menu. Then push the Next button to get to the second selection "PUt" or Power Up Test
setting. Push Enter. If the test is "On" push Next to turn it "OFF" (flashing) then push Enter to confirm the change (solid) and push
Enter again to return to "PUt" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal operation.
3.5.3 Selecting Display Option – "dSP"
To select the Display Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the
Enter button to enter the Con menu. Then push the Next button to get to the third selection "dSP" or Display setting. Push Enter. If
the display is "On" push Next to turn it "OFF" (flashing) then push Enter to confirm the change (solid) and push Enter again to return to
"dSP" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal operation.
3.5.4 Selecting Buzzer Option – "bUZ"
To select the Buzzer Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the
Enter button to enter the Con menu. The fourth selection is the "bUZ" or Buzzer setting. Push Next twice to get to "bUZ" then Enter. If
the display is "On" push Next to turn it "OFF" (flashing) then push Enter to confirm the change (solid) and push Enter again to return to
"bUZ" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal operation.
3.5.5 Selecting Alarm Relay Setting – "ArS"
To select the Alarm Relay Setting, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the
Enter button to enter the Con menu. The fifth selection is the "ArS" or Alarm Relay Setting. Push Next three times to get to "ArS" then
Enter. If the display is "dIS" (disabled) push Next to change it to 900, 1000, 1100, 1200, ..., 4000 (default), 4800, 4900, 5000 ppm
(flashing) then push Enter to confirm the change (solid) and push Enter again to return to "ArS" in the Con menu. Push Next until "End"
is displayed then push Enter to get back to normal operation.
3.5.6 Selecting Alarm Relay Configuration – "Arc"
To select the Alarm Relay Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push
the Enter button to enter the Con menu. The sixth selection is the "Arc" or Alarm Relay Configuration. Push Next four times to get to
"Arc" then Enter. If the relay is "nO" (normally open) push Next to turn it to "nC" (flashing) then push Enter to confirm the change (solid)
and push Enter again to return to "Arc" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal
operation.
3.5.7 Selecting Fan Relay Settings – "FrS"
To select the Fan Relay setting, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the Enter
button to enter the Con menu. The seventh selection is the "FrS" or Fan Relay setting. Push Next five times to get to "FrS" then
Enter. If the fan relay is "dIS" (disabled) push Next to change it to 600, 700, 800, 900..., 2000 (default)..., 4800, 4900, 5000 ppm (flashing)
then push Enter to confirm the change (solid) and push Enter again to return to "FrS" in the Con menu. Push Next until
"End" is displayed then push Enter to get back to normal operation.
3.5.8 Selecting Fan Relay Delay – "Frd"
To select the Fan Relay Delay setting, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push the
Enter button to enter the Con menu. The eighth selection is the "Frd" or Fan Relay Delay. Push Next six times to get to "Frd" then
Enter. If the delay is "0" (disabled) push Next to change it to 1, 3, 5, or 10 minutes (flashing) then push Enter to confirm the change
(solid) and push Enter again to return to "Frd" in the Con menu. Push Next until "End" is displayed then push Enter to get back to
normal operation.
14