Quick Set Operations; Pre-Charge Status; Charging By Battery Type - Optima Digital 400 Guide De L'utilisateur

Quick Set Operations

After connecting to a battery:
With your OPTIMA ® Digital 400 set up as outlined in pages 18-20, you can now make quick and easy
selections. With the charger plugged into a GFCI protected 110 VAC outlet, and properly connected to a
battery, the OPTIMA ® Digital 400 will automatically perform a quick self-test of the display and all LEDs.
Following the self-test you will be prompted by the display and the battery type LEDs will flash indicating
the Digital 400 is ready to charge or maintain. The LCD screens you will see:
50
25 75
0 100
% Charge
F
E
OPTIMA
DISPLAY CHECK
Volts DC Amps DC
00.0 0.0
see manual
Display Check Make a Quick Set Selection Prompt
Note: Self test takes less than 2 minutes. If after 10 minutes no selection is made,
the OPTIMA ® Digital 400 will automatically default to a safe charging/maintaining mode.
Note: It is recommended to make a selection and allow the charger to finish that selection
before making a different selection.
Below is an overview of each function that can be selected.
1. Pre-Charge Battery Status.
Note: Vehicle engine and all charging systems must be off.
This quick and easy feature allows you to understand your battery's state of charge before
charging it. To use this feature, use the battery pre-charge status function. The LCD display will
provide the current state of battery in % of charge and DC volts in the numeric display. Below
is a typical sequence of the display during this selection.
50
25 75 25
0 100 0
% Charge % Charge
E F E
PRE-CHARGE BATTERY
BATTERY STATUS NORMAL
Volts DC Amps DC Volts DC
00.0 0.0 13.4
see manual see manual
Normal Charge Status
Processing
Note: If the charger identifies a fault during this process or any quick set process it will
illuminate the "Check Battery" icon on the charger. Read the fault message and attend
to the battery or charger. See pages 23 and 24 for Fault Screens and Troubleshooting steps.
21
Digital 400
50
25 75
0
100
% Charge
E F
MAKE A QUICK SET
SELECTION NOW
50 50
75 25 75
100 0 100
% Charge
F E F
DEEP DISCHARGE
SELECT CHARGE
Amps DC Volts DC Amps DC
0.0 7.0 0.0
see manual
Deeply Discharged Status;
From here you can make a
Quick Set Charge Selection
for your battery type.
Quick Set Operations
2. Quick Set Charging by Battery Type.
From the battery type selector choose the BATTERY TYPE that matches the battery type descriptions
as outlined on page 17 titled: "Charging Battery Types & Approximate Charge Times."
After selecting 1 of the 4 battery types the charger will begin its stage 1 "Analyzing Battery" mode. This
mode can take up to 2 minutes to complete while it determines the state of your battery and check that
all connections made are correct. The charger is charging and testing the battery at this time.
Upon completing the Stage 1 "Analyzing Battery" mode, the charger will start its multi-stage
charging process checks and will sequence through the illustrated LCD screens highlighted below:
Analyzing Battery Mode (screen not shown)
Charging Battery Mode
Conditioning Battery Mode
Maintaining Battery
30 Day Recondition Mode
Profile 1
50 50
Engine
75 75
25 25
Starting
0 0
100 100
% Charge % Charge
E F E F
CHARGING 12V CONDITIONING 12V
OPTIMA BATTERY OPTIMA BATTERY
Volts DC Amps DC Volts DC Amps DC
10.5 3.5 14.6 1.5
see manual see manual
Profile 2
50 50
Deep Cycle 25 75 25 75
0 0
100 100
% Charge % Charge
E F E F
CHARGING 12V CONDITIONING 12V
OPTIMA BATTERY OPTIMA BATTERY
Volts DC Amps DC Volts DC Amps DC
10.5 3.5 14.6 1.5
see manual see manual
Profile 3
50 50
Auto/Marine
25 75 25 75
0 0
100 100
% Charge % Charge
E F E F
CHARGING 12V CONDITIONING 12V
LARGE BATTERY LARGE BATTERY
Volts DC Amps DC Volts DC Amps DC
10.5 3.5 14.6 1.5
see manual see manual
Profile 4
50 50
Motorcycle
75 75
25 25
0 0
100 100
% Charge % Charge
E F E F
CHARGING 12V CONDITIONING 12V
SMALL BATTERY SMALL BATTERY
Volts DC Amps DC Volts DC Amps DC
10.5 3.5 14.6 1.5
see manual see manual
Note: If the charger identifies a fault during this process or any quick set process it will
illuminate the "Check Battery" icon on the charger. Read the fault message and attend
to the battery or charger. See pages 23 and 24 for Fault Screens and Troubleshooting steps.
Digital 400
50 50 50
75 75 75
25 25 25
0 0 0
100 100
% Charge % Charge % Charge
E F E F E
MAINTAINING 12V OPTIMA 30 DAY MAINTAINING 12V
OPTIMA BATTERY 3 HR RECONDITION OPTIMA BATTERY
Volts DC Amps DC Volts DC Amps DC Volts DC Amps DC
13.4 1.0 13.4 1.0 13.4 1.0
see manual see manual see manual
50 50 50
25 75 25 75 25 75
0 0 0
100 100
% Charge % Charge % Charge
E F E F E
MAINTAINING 12V OPTIMA 30 DAY MAINTAINING 12V
OPTIMA BATTERY 3 HR RECONDITION OPTIMA BATTERY
Volts DC Amps DC Volts DC Amps DC Volts DC Amps DC
13.4 1.0 13.4 1.0 13.4 1.0
see manual see manual see manual
50 50 50
25 75 25 75 25 75
0 0 0
100 100
% Charge % Charge % Charge
E F E F E
MAINTAINING 12V 30 DAY 3 HR MAINTAINING 12V
LARGE BATTERY 12V RECONDITION LARGE BATTERY
Volts DC Amps DC Volts DC Amps DC Volts DC Amps DC
13.4 1.0 13.4 1.0 13.4 1.0
see manual see manual see manual
50 50 50
75 75 75
25 25 25
0 0 0
100 100
% Charge % Charge % Charge
E F E F E
MAINTAINING 12V 30 DAY 3 HR MAINTAINING 12V
SMALL BATTERY 12V RECONDITION SMALL BATTERY
Volts DC Amps DC Volts DC Amps DC Volts DC Amps DC
13.4 1.0 13.4 1.0 13.4 1.0
see manual see manual see manual
100
F
100
F
100
F
100
F
22