Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Ordering Replacement Parts - Toolson PRO-RF 521 Mode D'emploi

6.4 45° Lengthwise cut, "jolly cut" (Fig.11)
•
Loosen the star grip screw (10).
•
Tilt the guide rail (7) to the left to 45° on the
angle scale (17).
•
Retighten the star grip screw (10).
•
Cut as described in 6.2.
6.5 Changing the diamond cutting wheel
(Fig. 12/13)
•
Pull out the power plug.
•
Unscrew the four screws (35) and remove the
safety hood (8) for the blade.
•
Using the wrench (34), loosen the flange nut
in the direction of rotation of the cutting wheel
(2). (Notice! Left-hand screw-thread.) To do
so, place the wrench (31) on the motor shaft
and apply counterpressure.
•
Remove the outer flange (36) and cutting
wheel (2).
•
Clean the mounting flange thoroughly before
fitting the new cutting wheel.
•
Fit the new cutting wheel by following the
above procedures in reverse and then tighten.
Notice! Pay attention to the direction of rotati-
on of the cutting wheel!
•
Mount the safety hood (8) for the blade again.
6.6 Operating the LED light (Fig. 15-16)
Danger! Never look directly into the LED
light!
6.6.1 Stationary operation (Fig. 15)
To switch on: Move the ON/OFF switch (46) to
the "1" position.
To switch off : Move the ON/OFF switch (46) to
the "0" position.
Switch on the LED light (45). The work area is
now illuminated. You can additionally adjust the
LED light with the screw (47). To do so, undo the
screw (47) by a few turns. The LED light (45) can
now be moved and adjusted vertically and hori-
zontally on the adapter (48).
When the LED light is in the desired position, re-
tighten the screw (47).
6.6.2 Operation as a torch light/spirit level
(Fig. 15)
Remove the screw (47). The LED light can now
be taken off the adapter (48) and used as a torch
light. The base plate (50) of the LED light is ma-
gnetic, enabling it to be secured on suitable sur-
faces. You can also use the LED light as a leveling
aid using the integrated spirit levels (49).
Anl_PRO_RF_521_SPK7.indb 19 Anl_PRO_RF_521_SPK7.indb 19
GB
6.6.3 Replacing the battery
Unscrew the 4 screws (51) and remove the base
plate (50). Take out the old batteries and replace
with new ones. Then screw the base plate (50)
back on.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Remove dust and dirt from the machine at
regular intervals. Cleaning is best carried out
with a rag or brush.
•
Never use caustic agents to clean plastic
parts.
•
The trough (3) and the cooling water pump
(13) must be cleaned at regular intervals or
proper cooling of the diamond cutting wheel
(2) will not be guaranteed.
8.2 Maintenance
Lubricate all moving parts at regular intervals.
8.3 Transport
•
The coolant must be drained completely be-
fore transport.
•
Do not lift the machine by any of the safety
devices.

8.4 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
- 19 -
23.04.15 11:17 23.04.15 11:17