Worx HYDROSHOT WG620 Mode D'emploi page 13

OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
ASSEMBLY & OPERATION
ACTION
BEFORE OPERATION
Installing the battery pack
Removing the battery pack
Charging the battery pack
More details can be found in
WA3881manual
OPERATION
Attaching pressure cleaning lance to the
power nozzle
NOTE: When attaching, align the two
projections on the lance with the grooves of
the power nozzle as shown in Fig. B.
NOTE: The highest pressure is 350 psi(24
bar). It is suitable for removing strong stains.
Attaching the multi-spray nozzle
NOTE: when attaching, rotating the nozzle
left and right to make sure the nozzle fully
seated into position and gently pulling
it to make sure it is locked into position
securely.
Attaching the draw hose to the power
nozzle
NOTE: After the draw hose is attached,
check the connection by gently pulling
upon the draw hose. It should not be
pulled off.
Attaching your own water hose (optional)
1. Attach the quick connect adapter
2. Attach the home garden hose with
suitable connectors
NOTE: Except for the draw hose supplied,
you can also connect the power nozzle
to your own water hose with suitable
connectors.
NOTE: Check whether the filter screen
is missing before retightening the hose
adapter. (Fig. P1, P2) When retightening
the hose adapter, please tighten securely.
Otherwise, it may not draw any water for
proper operation.
WARNING: It is not recommended
to connect the draw hose to your
garden hose or your home tap.
Cordless Portable Power Cleaner
Start
NOTE: At the first use or after long-
term storage, it is recommended to
attach the tap or wait for several
minutes to empty the air until the
water goes up along the hose and
sprays out.
Selecting the nozzle pattern
FIGURE
NOTE: Choose a suitable nozzle pattern
according to your work. Spray patterns
0 , 15 , 25
0 0
See Fig. A1
cleaning, and the spray pattern with the
symbol
See Fig. A2
WARNING: Do not shift the nozzle
pattern when the tool is powered on.
See Fig. A3
Cleaning
WARNING: Do not connect the
machine to water supplies that
are dirty, rusty, muddy, or corrosive.
(Including window cleaning liquids,
plant foods, or fertilizers etc.)
NOTE: Not recommended for use with salt
See Fig. B
water, immediately rinse with fresh water
for proper maintenance.
Watering
ATTACHMENT OF
See Fig. C
ACCESSORIES
A number of accessories have been supplied with this
product and are required for use in different
applications. Do not attempt to use the cleaner with no
lance or accessories attached.
See Fig. D1,
D2
1. Soap bottle (WA4036, sold separately)
Soap bottle provides detergent suds for deeper cleaning of
dirt. It is used in conjunction with power nozzle
or extension lance (WA4012). (See Fig. J1, J2)
2. Brush (WA4048, sold separately)
Brush is for cleaning cars, boats, motorcycles etc. It is
used in conjunction with power nozzle or extension lance
(WA4012). (See Fig. K1, K2)
3. Window squeegee with water sprayer (WA4050,
sold separately)
See Fig. E, F
The window squeegees quick connection easily snaps into
the tool to spray water or wipe off water from glass or tiled
surfaces. Suitable for the HYDROSHOT
extension lance (WA4012). (See Fig. L1, L2, L3, L4)
4. Bottle cap connector (WA4038, sold separately)
The bottle cap connector accessory allows the tool
to directly connect with most 2 Liter bottles with
approximately 1" openings. (NOTE: May not fit all
consumable soda and water bottles) (See Fig. M1, M2, M3)
WARNING: Do not install the bottle cap connector
accessory until it is ready to be used. The
accessories vents will leak liquid, if a bottle is installed,
with the machine lying on a surface.
and 40 are applicable for
0 0
is best suitable for watering.
See Fig. G
See Fig. H
See Fig. I1
See Fig. I2
13
power cleaner or
TM
EN