Conrad Curve Mode D'emploi page 3

O P E R A T I N G I N S T R U C T I O N S
LED Outdoor Wall Light
"Curve", 3 W
Item no. 39 97 31
Intended Use
The product is intended to provide outdoor lighting. The product is intended for mounting on
a vertical wall.
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this product and involves
the risk of short circuits, fi re, electric shock, etc. No part of the product may be modifi ed or
converted!
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package Contents
• LED outdoor wall light
• Mounting material (screws, wall plugs)
• Operating instructions
Explanation of Symbols, Inscriptions
This symbol indicates a health hazard, e.g. electric shock.
The icon with an exclamation mark indicates particular dangers associated with
handling, function or operation.
The "Hand" symbol indicates special tips and operating information.
The product cannot be dimmed.
Observe the operating instructions!
Safety Instructions
Read the complete operating manual carefully before using the product, as it
contains important information about the correct installation and operation.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! The
warranty will be void in such cases!
Caution!
The product may be installed only by a qualifi ed technician (e.g. electrician)
who is familiar with the relevant regulations (e.g. VDE, German electrical wir-
ing regulations)!
Improper work carried out at the mains voltage endangers not only your life
but also the life of others!
If you do not have the expertise required for the installation, do not install it
yourself but entrust the work to a qualifi ed electrician.
a) General instructions
• Unauthorised conversion and/or modifi cation of the product is not allowed for
safety and approval reasons (CE).
• The product is not a toy and should be kept out of the reach of children. There is
danger of a life-threatening electric shock!
• If it can be assumed that safe operation is no longer possible, the device must be
turned off (take out corresponding fuse or switch off automatic cut-out; switch off
corresponding ground fault circuit interrupter) and precautions are to be taken to
ensure that it is not used unintentionally. After this, arrange for an expert to check
the product.
Safe operation can no longer be assumed if:
- the device shows visible signs of damage,
- the product does not work at all or works poorly (where there is fl ickering light,
leaking smoke or a smell of burning, audible crackling noises, or discolouration
to the product or to adjacent surfaces)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
www.conrad.com
Version 03/13
Preparations for Installation
• Without fail, pay attention to the correct mounting position
for the LED outdoor wall light; it must only be mounted so
the light points downwards.
Please note the illustration at right for this.
• Make sure you install the LED outdoor wall light only on a
solid base, e.g. brickwork. Use screws and, if necessary,
screw anchors that are suitable for the surface.
• The LED outdoor wall light must be installed and used out of the reach of children.
• Select the mounting height depending on the on-site conditions. We recommend a mounting
height of approx. 1.5 – 2 m.
• The LED outdoor wall light must be secured on the user's distribution board by a 10/16A fuse.
An earth circuit fault interrupter must be installed before this (FI protective switch).
• The LED outdoor wall light must be current/voltage-free during installation. It is not suffi cient
to just turn off the light switch!
First switch off all poles of the mains supply by removing the fuse or switching off at the circuit
breaker; then also switch off the associated residual current circuit breaker. Secure it against
unauthorised reconnection, e.g. with a danger sign.
• Check the mains connection for absence of voltage using a suitable meter.
• Never direct a jet of water (e.g. for cleaning) from a garden hose or high-pressure
cleaner, or similar source, onto the product!
• Caution, LED light:
Do not look directly into the LED light!
Do not look into the beam directly or with optical instruments!
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• The accident prevention regulations of the association of compensation insurers
must be followed when using all electrical facilities and equipment in commercial
locations.
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.
b) Installation
• The product is protected according to IP44; it can be mounted and operated in-
doors and outdoors. Pay attention to the correct mounting position; see chapter
"Connection and mounting".
The product is suitable for use outdoors; however, it must never be used in or
under water!
• Only use the product when it is securely installed and steady.
• When installing, make sure that the connecting cable is not kinked, pinched or
damaged by sharp edges.
• Do not use this product in rooms or under adverse environmental conditions where
combustible gases, vapours or dust are or may be present! There is a risk of explo-
sion!
• Handle the product with care; it has sharp edges.
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress.
• Do not attach any items (e.g. decorations) to the product; there is a risk of fi re!
c) Connection
• The product may be operated only on the mains voltage (see section "Technical
Data"). Never try to operate the device using any other voltage.
During installation, all poles must be disconnected from the mains voltage (e.g. via
RCD).
• The product is designed according to Protection Class I; the protective earth con-
ductor must be connected.
If there is not a mains supply provided with a protective earth conductor at the
place of installation, the product must not be connected/used there. In this case,
install a new voltage supply with a protective earth wire.
• Connection is allowed only under zero-voltage conditions. First switch off all poles
of the mains supply by removing the fuse or switching off at the circuit breaker;
then also switch off the associated residual current circuit breaker. Secure it
against unauthorised reconnection, e.g. with a danger sign. Check the mains con-
nection for absence of voltage using a suitable tester.
• The product cannot be dimmed.
• Make sure that all electrical connections and connection cables correspond to the
regulations and to their operating instructions.