Table des Matières
Publicité
Liens rapides
INSTALLATION & OPERATION MANUAL
HEAVY DUTY GAS GRIDDLES
ITW Food Equipment Group, LLC
3600 North Point Blvd.
Baltimore, MD 21222
MODELS
924RX
936RX
948RX
960RX
972RX
MSA24
ASA24
MSA36
ASA36
MSA48
ASA48
MSA60
ASA60
MSA72
ASA72
AGM24
AGM36
AGM48
AGM60
AGM72
948RX
MSA48
AGM48
RETAIN THIS MANUAL FOR FUTURE USE
FORM F-38315 (rev. 08-10)
Publicité
Table des Matières
Manuels Connexes pour ITW Food Equipment Group VULCAN Serie
Sommaire des Matières pour ITW Food Equipment Group VULCAN Serie
- Page 1 948RX MSA24 ASA24 MSA36 ASA36 MSA48 ASA48 MSA60 ASA60 MSA72 ASA72 MSA48 AGM24 AGM36 AGM48 AGM60 AGM72 AGM48 RETAIN THIS MANUAL FOR FUTURE USE ITW Food Equipment Group, LLC 3600 North Point Blvd. Baltimore, MD 21222 FORM F-38315 (rev. 08-10)
-
Page 2: Important
IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. -
Page 3: Table Des Matières
TABLE OF CONTENTS GENERAL…………………………………………………………………………………………...…...… Specifications……………………………………………………………………………………..INSTALLATION……………………………………………………………………………………………. Unpacking………………………………………………………………………………………………. Location…………………………………………………………………………………………………. Installation Codes and Standards……………………………………………………………………. Griddle Mounted On Stands with Casters…………………………………………………………… Flue Connections………………………………………………………………………………………. Stands…………………………………………………………………………………………………… Gas Connections……………………………………………………………………………………….. Testing the Gas Supply System……………………………………………………………………… Gas Pressure Regulator Installation…………………………………………………………………. Electrical Connection – 900RX Models……………………………………………………………… OPERATION……………………………………………………………………………………………….. Before First Use………………………………………………………………………………………… Seasoning the Griddle…………………………………………………………………………………. -
Page 4: General
INSTALLATION, OPERATION AND CARE OF HEAVY DUTY GAS GRIDDLES GENERAL Heavy Duty Gas Griddles are produced with quality workmanship and materials. Proper installation, usage and maintenance of your griddle will result in many years of satisfactory performance. Thoroughly read this entire manual and carefully follow all of the instructions provided BTU/hr Input Model Number of Burners... -
Page 5: Installation Codes And Standards
Do not permit air to blow directly at the griddle. Avoid open windows next to the griddle wherever possible. Avoid wall-type fans which create air cross-currents within the room. This griddle is Design Certified for installation on a non-combustible counter with 4” legs, or combustible floor with 25”... -
Page 6: Flue Connections
If disconnection of the restraint is necessary, turn off the gas supply before disconnecting. Reconnect the restraint prior to turning the gas supply on and returning the griddle to its installation position. Casters are only supplied on a griddle stand. If the griddle is moved for any reason the griddle should be re-leveled (see LEVELING in this manual). -
Page 7: Gas Pressure Regulator Installation
GAS PRESSURE REGULATOR INSTALLATION A gas pressure regulator is supplied with the griddle and must be installed. Install the regulator as close to the griddle on the gas supply line as possible. Make sure that the arrow on the underside of the regulator is oriented in the direction of gas flow to the griddle (Fig. -
Page 8: Operation
OPERATION The griddle and its parts are hot. Use care when operating, cleaning or servicing the griddle. BEFORE FIRST USE Remove all packing material and protective plastic from the surfaces of the unit. Before leaving the factory the griddle is coated with vegetable oil as a rust inhibitor. Remove this film when the griddle plate is being cleaned prior to its first cooking use. - Page 9 This model features an electric ignition system that is controlled by a momentary power switch. The power switch turns the electric ignition system off and on only and will only supply power to the igniters when held down in the ON position. The burners and pilots will continue to work with power switch in the OFF position until the gas supply to the unit is cut off or the griddle gas shut-off valve is turned to the OFF position (Fig.
-
Page 10: Controls - Msa And Asa Models
CONTROLS – MSA AND ASA MODELS pilot adjustment screw pilot and burner sight holes thermostat knob Fig. 7 pilot safety valve push button This model features a standing pilot that must be manually lit with an outside ignition source (such as a lit taper, etc). The pilot is monitored by a thermocouple and pilot safety valve. -
Page 11: Controls - Agm Models
CONTROLS – AGM MODELS burner and pilot sight holes burner control knob Fig. 8 pilot adjustment screw The model is equipped with standing pilots. Gas will flow from the pilots as soon as the main gas supply to the unit is turned on. The pilots are lit with the use of an outside ignition source (such as a lit taper, etc). -
Page 12: Pilot Lighting Procedure - 900Rx Models
PILOT LIGHTING PROCEDURE – 900RX MODELS 1. Turn the griddle shut-off valve to the OFF position (See Fig.6 on page 9). Wait 5 minutes to allow any gas that may have accumulated in the burner compartment to escape. 2. Turn the griddle shut-off valve to the ON position (See Fig. 5 on page 9). 3. -
Page 13: Pilot Lighting Procedure- Msa And Asa Models
PILOT LIGHTING PROCEDURE- MSA AND ASA MODELS 1. Turn the main gas shut-off valve to the OFF position. Wait 5 minutes to allow any gas that may have accumulated in the burner compartment to escape. 2. Turn the main gas shut-off valve ON. 3. -
Page 14: Pilot Lighting Procedure - Agm Models
PILOT LIGHTING PROCEDURE – AGM MODELS 1. Turn the main gas shut-off valve and all burner control knobs to the OFF position. Wait 5 minutes to allow any gas that may have accumulated in the burner compartment to escape. 2. Turn the main gas shut-off valve ON. 3. -
Page 15: Using The Griddle
USING THE GRIDDLE To preheat, turn the burners on about 20-25 minutes before cooking. A uniform and systematic approach to loading the griddle will produce the most consistent product results. The griddle plate is steel, but the surface is relatively soft and can be scored or dented by careless use of a spatula or scraper. -
Page 16: Cleaning The Griddle
CLEANING THE GRIDDLE Empty the grease drawer as needed throughout the day and regularly clean at least once daily. Clean the griddle regularly. A clean griddle always looks better, lasts longer and performs better. To produce evenly cooked, perfectly browned griddle products keep the griddle plate clean and free of carbonized grease. -
Page 17: Adjustments
ADJUSTMENTS CALIBRATION-900RX AND MSA MODELS 1. Each thermostat controls a 12” zone of the griddle. Using a Surface Probe temperature measurement device, observe the temperatures at the center points of the cooking zones. These points are located by starting 6” from the side splash (left or right) and every 12”... -
Page 18: Leveling
LEVELING The griddle must be level (side-to-side and front-to-back) during operation to ensure proper performance. Improper leveling can result in uneven temperature distribution, cold spots, and possibly damage electrical components. 1. Place a level on the griddle. 2. Adjust legs by turning the bullet feet at the bottom of each leg. Using pliers or a crescent wrench, turn the feet counter-clockwise to increase height, and clockwise to decrease height until leveling is achieved. -
Page 19: Shutdown Of Griddle - Msa And Asa Models
SHUTDOWN OF GRIDDLE – MSA AND ASA MODELS 1. Turn thermostats to the OFF position to cut off burners. 2. The pilots will remain lit and monitored by the safety valve as long as the main gas supply is on. SHUTDOWN OF GRIDDLE WITH STANDING PILOT SYSTEM –... -
Page 20: Maintenance
MAINTENANCE The griddle and its parts are hot. Use care when operating, cleaning or servicing the griddle. LUBRICATION All valves must be checked and lubricated periodically. Check with your service agency for details. VENT Daily, when the griddle is cool, check the flue and clear any obstructions. SERVICE AND PARTS INFORMATION Contact the Service Agency in your area to obtain service and parts information. -
Page 21: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSES 1. Problem with thermostat or burner valve. (Call for service) Heat does not come on 2. Pilot burner not lit. when the thermostat or 3. Griddle shut-off valve not in ON position. burner valve is turned on 4. -
Page 22: Accessory Installation
ACCESSORY INSTALLATION The griddle and its parts are hot. Use care when operating, cleaning or servicing the griddle. SIDE VIEW ... -
Page 23: Front View
SIDE VIEW FRONT VIEW ... - Page 24 NOTES...