Page 2
All manuals and user guides at all-guides.com IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED.
Page 3
All manuals and user guides at all-guides.com INSTALLATION, OPERATION AND CARE OF GAS HOTPLATES GENERAL Gas Countertop Hotplates are designed for commercial use only and feature fast, efficient gas heat. Each burner is controlled by an adjustable gas valve. Cast grates and burners are easily removed for cleaning when cool.
Page 4
All manuals and user guides at all-guides.com INSTALLATION CODES AND STANDARDS The hotplate must be installed in accordance with: In the United States of America: 1. State and local codes. 2. National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition). This shall include but not be limited to: NFPA #54 Section 10.3.5.2 for Venting.
Page 5
All manuals and user guides at all-guides.com GAS CONNECTIONS Gas supply connections and any pipe joint compound must be resistant to the action of propane gases. Purge the supply line to clean out any dust, dirt, or any foreign matter before connecting the line to the unit.
Page 6
All manuals and user guides at all-guides.com OPERATION The hotplate and its parts are hot. Use care when operating, cleaning or servicing the hotplate. CONTROLS There is one pilot for every two burners. The hotplate is equipped with standing, unmonitored pilots. Gas will flow from the pilots as soon as the main gas supply to the unit is turned on.
Page 7
All manuals and user guides at all-guides.com PILOT ADJUSTMENT Using a flathead screwdriver, turn the slotted hex-head pilot adjustment screw clockwise to decrease the flame, and counterclockwise to increase the flame. See Fig. 6. Fig. 6 PILOT ADJUSTMENT SCREWS CLEANING The hotplate and its parts are hot.
Page 8
All manuals and user guides at all-guides.com MAINTENANCE The hotplate and its parts are hot. Use care when operating, cleaning or servicing the hotplate. LUBRICATION All valves must be checked and lubricated periodically. Check with your service agency for details. VENT SYSTEM At least twice a year the exhaust hood (venting system) should be examined and cleaned.
Page 9
All manuals and user guides at all-guides.com TROUBLESHOOTING Burner does not come on A. Problem with gas valve. (Call for service). when the control knob is B. Pilot burner not lit. turned on C. Low gas pressure. (Call for service) Too much heat A.
Page 10
All manuals and user guides at all-guides.com ACCESSORY INSTALLATION The hotplate and its parts are hot. Use care when operating, cleaning or servicing the hotplate. - 10 -...
Page 11
All manuals and user guides at all-guides.com - 11 -...
Page 12
All manuals and user guides at all-guides.com NOTES - 12 -...
Page 13
All manuals and user guides at all-guides.com...
Page 14
All manuals and user guides at all-guides.com...
Page 15
All manuals and user guides at all-guides.com...
Page 16
All manuals and user guides at all-guides.com...
Page 17
All manuals and user guides at all-guides.com...
Page 18
All manuals and user guides at all-guides.com...
Page 19
All manuals and user guides at all-guides.com...
Page 20
All manuals and user guides at all-guides.com...
Page 21
All manuals and user guides at all-guides.com...
Page 22
All manuals and user guides at all-guides.com...
Page 23
All manuals and user guides at all-guides.com...
Page 24
All manuals and user guides at all-guides.com...