Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
+
DA - DB
-
T1
T2
T
-
1 - 2
S1
2 - 3
OPEN
SAT1
SAT2
SAT3
DIP 1
Off
On
Off
DIP 2
Off
Off
On
DIP 3
Off
Off
Off
DIP 4
Off
Off
Off
DIP 5
Not used
DIP 6
Off
Disable the input link to zone n° 7 e zone n° 8
DIP 7
On
Enable the input link to zone n° 7 e zone n° 8
DIP 8
Not used
WHITE LED
It lights up when the antenna A is receiving
GREEN LED
It lights up when the antenna B is receiving
RED LED
It lights up when is in transmission
SENSOR PROGRAMMING IF COMBINED WITH XTREAM CONTROL PANELS
Parameter 1
Enab. accelerom.: setting to "YES" enables reporting of the strain and of disorientation of the radio sensor as TAMPER
Parameter 2
Low power mode: setting to "YES" enables the "Low consumption" of the radio sensor battery
Antimask sensit.: it is possible to adjust the sensitivity of the Antimask present in the sensor by setting 4 - 100% (Maximum) or
Parameter 3
3 - 75% or 2 - 50% . By setting to 1 - OFF the Antimask is not active
Parameter 4
IR Reduc. Sensit.: setting to "YES" enables a reduction in sensitivity of the infra-red
Parameter 5
IR Sig. integrat.: setting "Double pulse" activates a further reduction of the sensitivity of the infra-red
MW Sensitivity: it is possible to adjust the microwave sensitivity present in the sensor by setting 1 - 100% (max) or 2 - 75% or
Parameter 6
3 - 50% or 4 - 25%
Enab. IN1 term.: in the radio sensor WIC 4 / WIC 4 Plus, setting to "YES" enables functioning of the terminal input IN1
Parameter 7
NOTE: In case of double channel, configuration of both the sensors must be made exclusively on the one with the lowest
address
Puls. inert/SW-AL: in the WIC 4 / WIC 4 Plus radio sensor, it is possible to adjust the number of pulses of the input alarm IN1.
Parameter 8
1 = High sensitivity - 16 = Low sensitivity
Parameter 9
Vibration enable: in the WIC 4 / WIC 4 Plus radio sensor, setting to "YES" enables the integrated accelerometer "vibration" function.
Vibration sens.: in the WIC 4 / WIC 4 Plus radio sensor, it is possible to adjust the sensitivity of the accelerometer present in
Parameter 10
the sensor. 1 = High sensitivity - 8 = Low sensitivity
Vibration pulses number: it is possible to adjust the number of pulses of the Accelerometer present in the sensor. 1 = Very
Parameter 11
sensitive - 16 = Little sensitive
SIRENA RADIO PROGRAMMING IF COMBINED WITH XTREAM CONTROL PANELS
Parameter 1
Enab. accelerom.: setting to "YES" enables reporting of the strain and of disorientation of the radio siren as TAMPER
Parameter 2
Max time alarm: One minute/three minutes
Sound level: there is a choice of 8 Levels. The values are relative to the sound level of both the Main Sound and the Alternative
Parameter 3
Sound. 1 is the Maximum and 8 is the Minimum.
Parameter 4
Principal sound tone: it is possible to select one of 8 tones for the Principal Sound
Parameter 5
Power supply type: select the type of power supplied to the siren between 1 - Battery 6V or 2 - Power supply 12V + Battery
Tamper active siren: setting to "NO", in case of tamper / antitear opening the siren transmits the event and sounds according
Parameter 6
to the schedule of the combined central unit setting to "YES", if the tamper / tear-off is opened, the siren transmits the event and
sounds autonomously for the time set "Max. sound "or based on commands sent from the combined control panel.
Parameter 7
Flash on / off: enables the siren flash to flash the on / off of the central office;
Parameter 8
Vibration enable: setting to "YES" enables the integrated accelerometer "vibration" function.
Vibration sens.: it is possible to adjust the sensitivity of the accelerometer present in the siren. 1 = High sensitivity - 8 = Low
Parameter 9
sensitivity.
Vibration pulses number: it is possible to adjust the number of pulses of the Accelerometer present in the siren. 1 = Very
Parameter 10
sensitive - 16 = Little sensitive
TERMINAL BLOCK
Positive power
DA / DB RS485 serial connection port
Negative power
Manages the input link to zone n° 7 and / or open collector output (OC 7)
Manages the input link to zone n° 8 and / or open collector output (OC 8)
Tamper input (TAMPER) balanced with reference to negative.
Negative
TAMPER Button: DISABLED - Input T: DISABLED (ALLOW FREE ENTRY T)
TAMPER Button: ENABLE - Input T: DISABLED (ALLOW FREE ENTRY T)
TAMPER Button: ENABLE - Input T: ENABLED
DIP SWITCH
SAT4
SAT5
SAT6
SAT7
On
Off
On
Off
On
Off
Off
On
Off
On
On
On
Off
Off
Off
Off
LED MULTICOLOR
JUMPER
SAT8
SAT9
SAT10
SAT11
On
Off
On
Off
On
Off
Off
On
On
Off
Off
Off
Off
On
On
On
- 7 -
SAT12
SAT13
SAT14
SAT15
On
Off
On
Off
On
Off
Off
On
Off
On
On
On
On
On
On
On
SAT16
On
On
On
On
Publicité
Table des Matières
