Before Use - Morphy Richards POWER STEAM ELITE 42221 Instructions

Features
Dry ironing
To use your steam generator as a dry iron only, follow steps 2
and 3 of 'Using the Steam Generator for steam ironing' on page
5. You do not need to put water in the tank or select a steam
level. Press either the steam boost button (1) (certain models
only) or the steam trigger (2) at least once every 10 minutes, or
the product will automatically turn off.
Auto shut-off (certain models only)
If either the steam boost button (1) (certain models only) or the
steam trigger (2) is unused for 10 minutes, the product will
automatically turn off, both for safety and to save energy.
To restart, press the On/Off button (16) (see step 2 of 'Using the
Steam Generator for steam ironing' on page 5) and wait for the
temperature to rise again.
Steam function
During steaming, small amounts of water may be ejected from
the soleplate. This is normal and can be avoided by using the
steam for short amounts of time and only when the iron is at
the correct temperature (the temperature indicator light (5) on
the iron goes out when ready).
Sudden jolts of the boiler unit can also cause water droplets on
the soleplate; therefore, do not move the base unit during
ironing. We recommend for first time ironing that you iron over
an old towel.
NOTE: The product may occasionally produce a pumping sound
during steam ironing. This is normal and is caused by water
being pumped through the steam generator.
Vertical steam 7
Vertical steam is useful for removing creases from hanging
clothes, curtains, wall hangings, etc. Hold the iron between
1cm and 2cm away from the item and press either the steam
boost button (1) (certain models only) or the steam trigger (2).
WARNING: Do not use the vertical steam feature on clothes
that are being worn.

Before use

• Remove any protective cover from the soleplate (3) and the base
unit, if any.
• Unwind and straighten the power cord (23) and steam supply cord
(22).
• Textiles and clothes should carry ironing instructions. If not, follow
the temperature guide on page 4, but test the temperature by
ironing the hem of the garment or similar discreet area first.
• It is advised to begin with 'cool' fabrics and work up to higher
settings. An iron heats up quicker than it cools down so you'll
save time and electricity.
• If you turn the temperature dial down from a hot setting to a
cooler setting, wait until the iron temperature has stabilised before
you continue ironing.
NOTE: Hold the base with both hands when handling and moving
the unit, as the water tank is detachable.
6
Maintenance
Cleaning the boiler
When the boiler requires descaling, the descaling indicator light
(19) will illuminate. When this happens, the boiler must be
manually rinsed out with clean water until all the scale is removed.
The indicator light will go out only after the scale has been
removed.
WARNING: Never remove the boiler screw (14) when the
steam generator is hot.
1 Unplug the appliance from the mains outlet and leave to cool for
two hours.
2 Remove the detachable water tank (8) and rest the iron (6) on its
heel on a firm surface next to a sink.
3 Hold the base unit (10) firmly with both hands and shake well.
4 Turn the base unit (10) upside-down and pull back the boiler cap
(15). Unscrew the boiler screw (14) with the boiler key (13), which
is attached to the underside of the base unit. If the screw is a bit
too tight to undo, try using a large screwdriver or a socket and
wrench set for more leverage.
5 Hold the base unit (10) over the sink, turn the unit the correct way
up to empty all water and loose scale from the boiler into the sink.
8
6 Using clean water, refill and empty the boiler repeatedly until all
scale has been rinsed out.
7 Replace the boiler screw, ensuring it is tightened fully. Replace the
boiler cap, boiler key, water tank and iron to the base unit.
WARNING: Ensure the boiler is empty before replacing the
boiler screw (14).
8 The descaling indicator light (19) will extinguish the next time you
use the product. Please wait for up to one minute whilst it pumps
water and registers that the boiler has been cleaned.
To clean a coated soleplate
Do not use scouring powder or solution as this could cause
damage to the coating.
If any man-made fibres fuse to the soleplate (4), set the iron at the
MAX position and pass it over a clean piece of cotton to draw the
deposit off the surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp cloth and mild
detergent, then wipe dry.
Emptying and storing
Allow the appliance to cool. Empty the water from the water
tank (8) by removing it from the base unit (10) and opening the
filling cap (7). Once the water tank is empty, re-attach it to the
base unit.
If the steam generator is not going to be used for a long time,
also empty the boiler as instructed, see 'Cleaning the boiler'.
To store, pull the cord clamp (12) outwards. Wrap the power
cord (24) and steam supply cord (23) around the base unit in
the cord storage groove (11). Secure the cord in place with the
cord clamp (12). Avoid kinking of cables, particularly at the exit
from the base unit.
9