Makita HR2300 Manuel D'instructions page 10

NOTE:
• If you connect a vacuum cleaner to your hammer,
cleaner operations can be performed. Dust cap needs
to be removed from the dust cup before the connection.
(Fig. 27)
OPERATION
Always use the side grip (auxiliary handle) and firmly
hold the tool by both side grip and switch handle during
operations.
Hammer drilling operation (Fig. 28)
Set the action mode changing knob to the
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light pres-
sure gives best results. Keep the tool in position and pre-
vent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
Set the action mode changing knob to the
CAUTION:
• There is tremendous and sudden twisting force exerted
on the tool/bit at the time of hole break-through, when
the hole becomes clogged with chips and particles, or
when striking reinforcing rods embedded in the
concrete. Always use the side grip (auxiliary handle)
and firmly hold the tool by both side grip and switch
handle during operations. Failure to do so may result in
the loss of control of the tool and potentially severe
injury.
NOTE:
• Eccentricity in the bit rotation may occur while operat-
ing the tool with no load. The tool automatically centers
itself during operation. This does not affect the drilling
precision.
Blow-out bulb (optional accessory) (Fig. 29)
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
Chipping/Scaling/Demolition
For Models HR2310T, HR2610, HR2610T, HR2611F,
HR2611FT
Set the action mode changing knob to the
Hold the tool firmly with both hands. Turn the tool on and
apply slight pressure on the tool so that the tool will not
bounce around, uncontrolled. Pressing very hard on the
tool will not increase the efficiency. (Fig. 30)
Drilling in wood or metal
For Models HR2300, HR2600, HR2601, HR2610,
HR2611F
Use the optional drill chuck assembly. When installing it,
refer to "Installing or removing the bit" described on the
previous page. (Fig. 31)
10
For Models HR2310T, HR2610T, HR2611FT
Use the quick change drill chuck as standard equipment.
When installing it, refer to "changing the quick change
chuck for SDS-plus" described on the previous page.
(Fig. 32 & 33)
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as
it will go. Hold the ring firmly and turn the sleeve clock-
wise to tighten the chuck. To remove the bit, hold the ring
and turn the sleeve counterclockwise. (Fig. 34)
Set the action mode changing knob to the
You can drill up to 13 mm diameter in metal and up to
32 mm diameter in wood.
symbol.
CAUTION:
• Never use "rotation with hammering" when the quick
change drill chuck is installed on the tool. The quick
change drill chuck may be damaged.
Also, the drill chuck will come off when reversing the
tool.
• Pressing excessively on the tool will not speed up the
drilling. In fact, this excessive pressure will only serve
to damage the tip of your bit, decrease the tool perfor-
mance and shorten the service life of the tool.
symbol.
• There is a tremendous twisting force exerted on the
tool/bit at the time of hole breakthrough. Hold the tool
firmly and exert care when the bit begins to break
through the workpiece.
• A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back out.
However, the tool may back out abruptly if you do not
hold it firmly.
• Always secure small workpieces in a vise or similar
hold-down device.
Diamond core drilling
When performing diamond core drilling operations,
always set the change lever to the m position to use "rota-
tion only" action.
CAUTION:
• If performing diamond core drilling operations using
"rotation with hammering" action, the diamond core bit
may be damaged.
Operation when using the dust cup (accessory)
(Fig. 35)
Operate the tool with the dust cup against the ceiling sur-
face.
g
symbol.
NOTE:
• The dust cup (accessory) is intended only for drilling in
the ceramic workpiece such as concrete and mortar.
Do not use the tool with the dust cup when drilling in
metal or similar. Using the dust cup for drilling in the
metal may damage the dust cup due to the heat pro-
duced by small metal dust or similar.
• Empty the dust cup before removing a drill bit.
• When using the dust cup, make sure that the dust cap
is mounted on it securely.
m
symbol.