DeWalt DXST4500PBK Guide D'utilisation

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113
(APR18) Part No. 41557
Copyright © 2018 D
D WALT and the D WALT Logo are trademarks of the D
®
E E
and are used under license. The yellow/black color scheme is a trademark for D
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please
read the manual and pay attention to these symbols.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided,
may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
CALL US TOLL FREE AT: 1-844-377-8451
WARNING! Read and understand all instructions.
important safety and operating instructions.
before assembling this storage rack and save it for reference.
SAVE THESE INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Technical Specifications
Height
Width
GENERAL SAFETY
• Keep work area clean and dry.
• Use correct/recommended tools for the job.
• Never leave tools unattended.
• Never force a part into place.
• Wear safety apparel.
• Wear safety glasses/goggles.
• Never crawl, sit, stand, or climb on a rack.
• Keep small parts away from children. Never leave a small child unattended while assembling.
• Always use common sense – your personal safety is your responsibility.
Parts List
No. Description
1 Metal Pegboard
2 Pegboard Mounting Beam
3 Side Mounting Bracket (Right)
4 Side Mounting Bracket (Left)
DXST4500PBK Copyright © 2018, D WALT
E
WALT.
E
WALT Industrial Tool Co., or an affiliate thereof
E
WALT power tools
E
& accessories.
WALT TOOL,
E
This manual contains
Please read this manual carefully
18" (45.72 cm)
47" (119.38 cm)
Qty. No. Description
2 5 Rear Mounting Bracket (Right)
2 6 Rear Mounting Bracket (Left)
4 7 Large Locking Pin
4 8 Small Locking Pin
1
2
Pegboard Assembly Orientations
NOTE: Pegboards can be mounted to the back or sides of racks for multi-functional organization.
NOTE: See images below for different pegboard mounting options.
*Double side panels
NOTE: DXST4500 Industrial Racks are sold separately.
BEFORE YOU BEGIN:
• Read all instructions thoroughly.
• Remove all components from the box, and lay them on the floor in an orderly fashion.
• Wear eye protection.
• Be cautious of sharp edges.
• Keep this information for further reference.
WARNING:
Serious or fatal crushing injuries can occur from rack tipping over. To prevent this, the
assembled rack must always be secured to a wall, especially in earthquake-prone environments, where
surfaces are uneven, and where children and/or pets are present.
Side Pegboard Panel Assembly (Fig. 1-3)
NOTE: This same process can be used for mounting double side panels.
1. Position one right and one left bracket onto the top two mounting slots of each upright on one side
Qty.
of the rack with the hanging tab arrows pointing upwards. Slide the side mounting brackets down
completely into the slots to secure them. For the bottom set of mounting brackets, offset them one
2
slot upwards from the bottom of the rack uprights then follow the same procedure as the top mounting
brackets. (Fig. 1)
2
2. Take the pegboard and position it to line up the holes on the pegboard with the hanging tabs on the
12
mounting brackets. Slide the pegboard onto the mounting brackets, and firmly push down on the top of
the pegboard to secure it onto the mounting brackets. (Fig. 2)
8
3. Insert a large locking pin into the hole on the top of each of the four (4) mounting brackets. (Fig. 3)
3
5
7
*Single side and back panels
READ ALL INSTRUCTIONS
4
6
8
*Double back panels