stayer TV509D Instructions D'emploi page 21

Masquer les pouces Voir aussi pour TV509D:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 22
Excessive feed considerably reduces the performance
capability of the machine and shortens the service life of
the cutting disc.
Use only cutting discs that are suitable for the material to
be worked.
Maintenance and service instructions
Cleaning
Before any work on the machine itself, pull the mains
plug.
Clean the ventilation slots of your power tool
regularly with a soft brush. The motor fan draws dust
into the housing, and a large accumulation of metal dust
can lead to electrical hazards.
In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a residual current device (RCD). When
working metals, conductive dust can settle in the interior
of the power tool. The total insulation of the power tool
can be impaired.
Have maintenance and repair work performed only
by qualified specialists. In this manner, it can be
ensured that the safety of the power tool is maintained.
The retracting blade guard must always be able to
move freely and retract automatically. Therefore,
always keep the area around the retracting blade guard
clean.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for STAYER
power tools.
Repair service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts. Exploded views and information on
spare parts can also be found under:
info@grupostayer.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
Disposal and recycling
The machine, accessories and packaging should be sor-
ted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/UE
for Waste Electrical and Electronic Equipment
and its implementation into national right, power
tools that are no longer usable must be collected
separately and disposed of in an environmentally
correct manner.
Subject to change without notice.
ENGLISH
21
Regulations
Technical Data
= Power input
= No load speed
rpm
= Disc dimension
Ø
Ins = Protection class
= Weigth
L
= Sound power level
WA
L
= Sound pressure level
A
P
= Vibration
The values given are valid for nominal voltages [U]
230/240 V ~ 50/60 Hz - 110/120 V ~ 60Hz. For lower
voltage and models for specific countries, these values
can vary. Please observe the article number on the type
plate of your machine. The trade names of the individual
machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN
62841-1. Typically the A-weighted noise levels of the
product are: Sound pressure level 97 dB(A); Sound
power level 108 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 62841-1:
Vibration emission value a
m/s².
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 62841-1 and may be used
to compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the
total working period..
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain
the tool and the accessories, keep the hands warm,
organisation of work patterns.
21
= 3.0m/s
, Uncertainty K =1.5
2
h

Publicité

Table des Matières
loading

Table des Matières