HK Audio ELEMENTS E 115 Sub D Manuel page 4

ELEMENTS E 115 Sub D 1.1
Thru
6
7
Ethernet
Data
In
Small Venue
Input
1
4
5
Cardioid Out
ELEMENTS
E 115 Sub D
MADE IN GERMANY
Mid/High Out
E 835
10
1+/1–
Power
12
Mains Input
Lock
100-240 V~
50-60 Hz
11
1.9 A @ 1/8
output power
4
13
Power
1 1x E 835
Auto Sleep
On Off
14
2 2x E 835
3 3x E 835
Preset
4 Remote
8
9
Thru Gain Sub
2 3
0 dB
+6 dB
Cardioid Setup
Front E 115 Sub D
L SUB 1500 A
Cardioid
Set Gain Bass
to +6 dB
Leave 1 meter
of space in each
direction!
Serial No.
Caution: Risk of electric shock! Do not open!
Refer servicing to qualified service personnel.
Attention: Risque de choc élèctrique –
ne pas ouvrir!
HK Audio is a brand of Stamer Musikanlagen GmbH
2 Connectors and Controls
●
1
Input
This XLR/ 1/4" (6.35 mm) combo jack provides a balanced input for analog
signals.
●
2
Thru
Use this parallel, balanced XLR output to send the signal routed into the
Input through to other components. This output remains active even when
the electronic components are deactivated.
●
3
Gain Sub
Use this knob to adjust the input gain for the incoming signal.
Heads up: This knob adjusts the volume of the E 115 Sub D. It does not
address or aff ect the connected mid/high units. We recommend starting
with it set to 0 dB at the center or 12 o'clock position.
●
4
Input/Limiter LED
This LED lights up green to indicate incoming signals and red to indicate
signal peaks. The LED briefl y fl ashes red to tell you the Limiter is
responding to signal peaks. If it stays red, turn down the Gain knob.
●
5
Cardioid Out
Connect a matching HK Audio LINEAR SUB 1500 A subwoofer to this output
when confi guring cardioid setups. See section 5.2 for more on this.
●
6
Ethernet In /Thru
Use the two Ethercon ports to integrate the speaker into a network. They
accept RJ45 and Ethercon (NE8 MX, NE8 MX6, NE8 MC) plugs. Use the
Ethernet Thru port to forward the network signal.
Always use S/STP or S/FTP cables to shield against electromagnetic
interference. We recommend CAT6 cables. A separate manual explains the
fi ner points of network integration, remote control functions and audio
streaming.
You will fi nd it on the ELEMENTS download page at www.hkaudio.com. For
a brief description of the DSP functions, see section
●
7
Data
This LED lights up orange when data fl ows through the network connector.
●
8
Preset
Use the Preset selection button to call up factory presets or a user preset
you can confi gure via the remote DSP CONTROL software. Tap the select
button once to scroll through Presets 1 through 4.
A separate manual explains how to program the four remote user presets.
You will fi nd it on the ELEMENTS download page at www.hkaudio.com.
Heads up: Selecting the proper preset tunes the subwoofer's frequency
response to match the frequency response of the connected mid/high
units. It is essential that you to do this manually because the power amp
cannot automatically detect the number of connected mid/high units.
Heads up: The numbers indicated for the Filter button always apply to
the E 835 model of mid/high unit. Be sure to multiply that number by
two when using the E 435 model.
●
8
Preset.