Basic Operation; Usb Operation; Aux Operation; Bluetooth Operation - Rockford Fosgate PUNCH Element Ready PMX-0 Mode D'emploi

Installation / Mounting / Operation
Contents
• Source Unit
• U Bracket & Nuts
• Installation & Operation
Manual
Installation Considerations
The following is a basic list of tools needed for installation:
• Volt/Ohm meter
• Wire strippers
• Wire crimpers
• Wire cutters
• #2 Phillips screwdriver
• Battery post wrench
• Hand held drill w/ assorted
bits
This section focuses on some of the vehicle considerations for installing
your new source unit. Pre-planning your system layout and best wiring
routes will save installation time. When deciding on the layout of your
new system, be sure that each component will be easily accessible for
making adjustments.
If you feel unsure about installing this system yourself, have it installed
by a qualified Rockford Audio technician.
Before installation, disconnect the battery negative (-) terminal to prevent
damage to the unit, fire and/or possible injury.
Before beginning any installation, follow these simple rules:
1. Be sure to carefully read and understand the instructions before
attempting to install the unit.
2. For safety, disconnect the negative lead from the battery prior to
beginning the installation.
3. For easier assembly, we suggest you run all wires prior to mounting
your unit in place.
4. Route all of the RCA cables close together and away from any high
current wires.
5. Use high quality connectors for a reliable installation and to minimize
signal or power loss.
6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel
lines, brake or hydraulic lines, vacuum lines or electrical wiring when
working on any vehicle.
7. Never run wires underneath the vehicle. Running the wires inside the
vehicle provides the best protection.
8. Avoid running wires over or through sharp edges. Use rubber
or plastic grommets to protect any wires routed through metal,
especially the firewall.
9. ALWAYS protect the battery and electrical system from damage with
proper fusing. Install the appropriate fuse holder and fuse on the
+12V power wire within 18" (45.7 cm) of the battery terminal.
10. When grounding to the chassis of the vehicle, scrape all paint from
the metal to ensure a good, clean ground connection. Grounding
connections should be as short as possible and always be connected
to metal that is welded to the main body, or chassis, of the vehicle.
Seatbelt bolts should never be used for connecting to ground.
• Heat shrink tubing
• Soldering iron
• Solder
• Heat gun
• 7mm wrench
Autogoods "130"

Basic Operation

TURNING THE UNIT ON / OFF
Press the POWER button to turn the unit ON or OFF
ADJUSTING THE VOLUME
Rotate encoder knob left or right to the desired volume level. You will
hear a beep when the VOLUME has reached it's maximum volume level.
ADJUSTING THE SUBWOOFER OUTPUT
Press the SUB + or SUB- buttons to adjust the output level. You will
hear a beep with the settings have reached their minimum and maximum
setting.
SELECTING A SOURCE TO PLAY
Press the SRC button to scroll through and select the audio source of
your choice. An audible notification will let you know what source is
selected (BLUETOOTH MODE>AUXILLARY MODE).

USB Operation

The USB port on the back of the device is for firmware updates and
charging devices only. Using it as an audio source will not work.

AUX Operation

After your device is plugged into the source unit, this feature allows you
to play music from your device. To select the AUX source, press the SRC
button until you hear "AUXILIARY MODE" over the speakers. You will use
your plugged in device to control song/track selection, PLAY/PAUSE and
track skip FWD/REV.
Bluetooth Operation
®
To pair your device to the source unit, you will need to go to your
Bluetooth settings on your device and select "Rockford PMX0".
After the initial pairing of your device, the volume will be set at 25%
volume. You will need to set the Volume on your device to 100% for
maximum sound.
Once your device is paired to the source unit, this feature allows you to
control playback from your device directly from the unit. To select the
BLUETOOTH source option on the source unit, simply press the SRC
button until you hear "BLUETOOTH MODE".
To play or pause a song, short press the PLAY/PAUSE button.
To skip a track forward, short press the FWD button. To skip a track
backwards, short press the REV button.
5