Self Help - Bosch SHE45C Guide D'entretien Et D'utilisation

Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The following informa-
tion may help you with a dishwasher problem without involving a repair professional.
Problem Cause
Dishwasher 1. Door may not be properly latched.
does not 2. Unit may not be turned on.
start 3. Unit not reset or previous cycle not complet-
ed.
4. Delay start engaged.
5. Interruption of electrical power supply to dish-
washer or blown fuse.
6. Child lock activated (select models).
7. The door may have been closed without first
selecting a cycle.
8. Water supply may not be turned on.
Dishwasher Default factory settings alert the customer that the
beeping cycle has completed by beeping. This feature can
(end of cycle be deactivated if so desired.
signal)
Display does 1. A fuse may have been blown or circuit breaker
not illumi- tripped.
nate or con- 2. Door not closed or latched.
sole lights Note: For models with controls on the top portion
are not on of the door, the display only illuminates when the door is
opened and controls are visible.
Dishwasher 1. Incoming water is not warm enough.
seems to run 2. Cycle time can vary due to soil and water condi-
a long time tions.
3. Rinse agent dispenser is empty.
4. Dishwasher connected to cold water supply.
Note: Refer to "Cycle Chart Data" section in this
manual for typical cycle length.
Dishes aren't 1. Spray arm movement is obstructed.
getting clean 2. Spray arm nozzles clogged.
enough 3. Improper use of detergents.
4. Filters could be clogged.
5. Dishes are nested or loaded too close to-
gether.
6. Selected wash cycle is not suitable for food soil
condtions.
Dishes are 1. Rinse agent dispenser is empty. (Rinse agent
not getting indicator is activated).
dry enough 2. Improper loading of dishes.
3. Selected cycle does not include drying.
Note: Plastic or Teflon do not typically dry as com-
pletely as other items due to their inherent proper-
ties.
18

selF Help

Action
1. Shut the door completely.
2. Press the main power switch to turn unit on.
3. To reset, refer to "Canceling or changing the cycle" section
in this manual.
4. To reset, refer to "Delay Start" section in this manual.
5. Check circuit breaker.
6. Deactivate the child lock. Refer to "Child Lock" section in
this manual if applicable.
7. Select a cycle and close the door.
8. Check and turn on water supply.
To adjust the volume or deactivate, refer to "Cycle Completion
Signal" section in this manual.
1. Check the fuse or circuit breaker box and replace the fuse
or reset the breaker if necessary.
2. Ensure that door is properly latched and completely
closed.
1. Before starting a cycle, run hot water faucet at the sink
nearest to the dishwasher.
2. Sensors in the dishwasher automatically increase the cycle
time to ensure a good wash when heavy soil is detected.
3. Add rinse agent.
4. Verify dishwasher is connected to hot water supply plumb-
ing.
1. Ensure that spray arm movement is not blocked by hand
rotating spray arms.
2. Remove the spray arms and clean according to "Check/
Clean the Spray Arm Nozzles" in Care and Maintenance
section of this manual.
3. Increase or decrease detergent depending on the water
hardness. Refer to Table under "Adding Detergent and
Rinse Agent".
4. Clean the filter. Refer to "Check/Clean the Filter System"
under Care and Maintenance section of this manual.
5. Rearrange load such that water spray can reach all items in
the dishwasher. See also "Preparing and Loading" section
of this manual.
6. Refer to "Wash Cycle" section in Operating the Dishwasher
section of this manual.
1. Add rinse agent. The use of rinse agent improves drying.
2. Rearrange load to ensure items are not nested. Refer
also to the "Preparing and Loading" section of this
manual.
3. Rinse and Hold setting does not include drying cycle,
Note: Select models offer an extra heating options to im-
prove drying performance. Refer to "Wash Cycle options"
under the Operating the Dishwasher section of this manual.