Battery Charger Configuration; Accessories; Installation Information; Battery Preparation - Lavorwash COMFORT XXS Mode D'emploi

2 On- board battery charger
3 Battery charger plug
4 Battery connection diagram
Photo H
1 Detergent solution ouflow adjusting lever
2 Battery security connector
2 Brush plate lifting/lowering lever
Photo I
1 Battery charger cover
2 Red LED - Battery discharged
3 Green LED - Full charged battery
4 Dip-Switches
5 Plastic cap to access the Dip-Switches
6 Dip-Switches for PB-Acid/GEL battery
setting
7 Table with Dip-Switch settings for
PB-Acid/GEL charging curve
Photo L
1 Unblocking lever of the electromechani-
cal brake in working position
(brake applied)
2 Unlocked position of the
electromechanical brake
Photo M
1 Steering wheel
2 Control panel with display
3 General ON/OFF key switch
4 Detergent tank
Photo N
1 Brush motor operating push button
2 Suction motor operating push button
3 Detergent outflow adjusting push button
4 Forward/reverse traction push button
selector
5 Traction speed increase push button
6 Traction speed reduce push button
7 Operating informations display
5.2.2 BATTERY
If supplied, the Pb-Acid (if not dry charged) or gel
batteries are ready to be installed:
Positive pole - red
Negative pole - black.
5.2.3 BATTERY CHARGER
If supplied, refer to the corresponding booklet.
5.3 BATTERY CHARGER CONFIGURA-
TION
We recommend to call the assistance centre or
a technician if you have problems with the setting
given.
The machine is equipped with a battery charger
configurated for PB-Acid batteries
If the operator whish to use GEL / AFGM batteries,
it is necessary change the battery charger settings
as follows:
DISPLAY OF THE BATTERY CHARGER SETTINGS
The battery charger settings are shown by the
blinking of the LED indicator when the battery
charger is switching on:
- the RED LED indicator ( Photo I - 2 ) flashes
2 times = the battery charger is set for PB-Acid
batteries
- the GREEN LED indicator ( Photo I - 3 )
flashes 2 times = the battery charger is set for
GEL batteries
The battery charger settings will be displayed even
if batteries are not connected.
DIP-SWITCH CONFIGURATION FOR BATTERY
CHARGER CBHD2 24V 20A
To set the charging curve type for Pb-Acid or
GEL/AGM batteries it is necessary to operate on
the dip-switches placed inside the battery
charger ( Photo I -4 ).
The dip-switches for the setting of the charging
curve are on the control card ( Photo I - 4 ) that
is placed behind the lower panel of the battery
charger ( Photo I - 1 ). It is also possible to reach
the dip-switches by removing the plastic cap (
Photo I - 5 ).
For the setting of the charging curve it is neces-
sary to operate on the dip-switches of the group
indicated as SW1 ( Photo I - 6 ), placing them
as shown in the table ( Photo I - 6) at page 7.
NOTE: The dip-switches of the group indicated as
SW2 must always be set in the OFF posi-
tion.
5.4

ACCESSORIES

Your machine supplier can provide a complete and
updated list of all available accessories, such as
brushes, pad drivers, disks, etc.

6. INSTALLATION INFORMATION

6.1

BATTERY PREPARATION

The technical features of the batteries used
must match those indicated in the technical fea-
tures section. Using different batteries may cause
serious damage to the machine or may require
them to be charged more frequently.
During installation or when performing any
type of battery maintenance, the operator must
be equipped with adequate safety accessories to
prevent accidents. Work far from open flames, do
not short-circuit the battery poles, do not generate
sparks and do not smoke.
The batteries are normally supplied full of acid so-
lution (for the Pb-Acid type) and ready for use. In
any case, follow the steps indicated in the manual
supplied with the battery and carefully follow the
33