Draining The Recovery Tank; Driving The Machine; Work Method; Preparation And Warnings - Lavorwash COMFORT XXS Mode D'emploi

• Remove the plug in the back of the machine.
• Leave 7 cm between the mouth of the plug and
the liquid level. Do not fill beyond this point!
• Add the required quantity of the chemical prod-
uct, considering the percentage indicated by the
supplier, with reference to the full tank capacity
listed on the product sheet.
• Use only those products suitable for the floor and
the dirt to be removed.
The machine was designed to be used
with non-foaming and biodegradable deter-
gents made specifically for scrubber-driers.
The use of other chemical products (such as
sodium hypochlorite, oxidisers, solvents or
hydrocarbons) may damage or destroy the
machine.
• Follow the safety regulations specified in the
relative section and indicated on the detergent
container.
• Contact the machine manufacturer to obtain a
complete list of available and suitable detergents.
• •Always add the detergent after filling the tank
with water to prevent foam from being created in-
side.
• Do not leave the water hose unattended and
insert it completely into the tank: the hose might
move and get sensitive parts of the machine wet.
• Close the tank cover.
To drain the solution water tank:
• Open the valve located at the bottom of the
machine in the back ( Photo D - 1 ) and wait until
the tank has been completely emptied.
• Close the drain valve.
7.5

DRAINING THE RECOVERY TANK

The dirty water must be drained in accordance with
national regulations.
The user is completely responsible for ensuring
compliance with such rules.
After the detergent solution is finished, always
empty the recovery tank before filling it again.
In general, the recovery tank can be emptied
whenever required, and even during intermediate
phases of the work cycle.
Always empty the recovery tank before lifting it
to avoid health problems for operators and to avoid
damaging the machine.
The recovery tank volume is higher than the de-
tergent solution volume, therefore a potentially
dangerous situation for the suction motor should
never occur. In any case, a safety float turns off
the suction motor if the dirty liquid level is too high.
If water or foam starts leaking from under the
tanks for any reason, immediately turn off the suc-
tion motor and empty the recovery tank.
To drain the tank:
Drive the machine to a suitable location to drain
the dirty water and preferably near a toilet or a
sewer drain (comply with the national regulations
for waste water disposal).
Turn off the machine and remove the key from the
panel.
Detach the drain hose from the hook and, keeping
it high, unscrew the plug.
Lower the drain hose toward the selected drain-
age point.
The emptying operation can be interrupted quickly
and whenever required just by raising the drain
hose.
Check the quantity of residual dirt in the tank and,
if necessary, clean the interior through the inspec-
tion hole, lifting the cover and the funnel at the
top.
Carefully position the funnel inside the inspection
hole and close the top cover, tightening the lock
handles after each inspection/cleaning operation.
Fully tighten the drain hose with the screw plug
and hang it on the support behind the machine.
☞ The top cover of the tank and the drain hose
plug must be airtight, otherwise the subsequent
pressure loss will reduce drying efficiency.
7.6

DRIVING THE MACHINE

Select the running direction using the Forward/
Reverse lever.
Insert and turn the ignition key.
Using the right foot lightly press the accelerator
pedal and drive the machine to its destination.
Turn off the machine and remove the keys from
the control panel.
The running direction can be changed using the
forward/reverse lever, even while pressing on the
accelerator pedal.
7.7

WORK METHOD

7.7.1

PREPARATION AND WARNINGS

Remove any loose solid residue from the surface
to be treated (using suitable tools, such as vacuum
cleaners, sweepers, etc.). It this is not done, the
solid dirt might prevent the squeegee from operat-
ing correctly, reducing drying efficiency.
This machine can driven only by trained personnel.
7.7.2

OPERATING CONTROLS

• Ignition key, to turn the machine on and off.
• Direction lever, to select forward or reverse move-
ments.
• Speed regulator, to select the maximum advance-
ment speed when the pedal is fully depressed.
• Brush switch, to turn on the brush rotation motor.
• Brush position switch, to lower (work position) or
raise (rest/movement position) the brush unit on/
from the floor.
• Suction switch, to turn on the suction motor.
• Squeegee position switch, to lower (work posi-
tion) or raise (rest/movement position) the squee-
gee.
• Emergency switch, to cut off/restart all pro-
36