Publicité
Les langues disponibles
Les langues disponibles
U-Support
C-Connector
Spring-loaded Pin
Size of pool
QTY Part No. QTY
111inx77inx33in
16
4
P61361
(2.82mx1.96mx84cm)
159inx79inx39.5in
20
4
P61361
(4.04mx2.01mx1.00m)
162inx79inx48in
4
P61361
20
(4.12mx2.01mx1.22m)
16ftx9ftx48in
4
P61282
24
(4.88mx2.74mx1.22m)
16ftx16ftx48in
4
P61282
32
(4.88mx4.88mx1.22m)
18ftx9ftx48in
4
P61282
24
(5.49mx2.74mx1.22m)
22ftx12ftx52in
4
P61282
32
(6.71mx3.66mx1.32m)
24ftx12ftx52in
4
P61282
36
(7.32mx3.66mx1.32m)
31.3ftx16ftx52in
4
P61282
48
(9.56mx4.88mx1.32m)
C-Connector
Top Rail
Top Rail
U-Support B
U-Support A
NOTE:
Drawing only for (111in x 77in x 33in), (159in x 79in x 39.5in),
(162in x 79in x 48in) Size of Pool.
NOTE:
Drawing for illustration purpose only. May not reflect actual product. Not to scale.
No. of U-shaped
Size of pool
support
111inx77inx33in
8
(2.82mx1.96mx84cm)
159inx79inx39.5in
10
(4.04mx2.01mx1.00m)
162inx79inx48in
10
(4.12mx2.01mx1.22m)
16ftx9ftx48in
12
(4.88mx2.74mx1.22m)
16ftx16ftx48in
(4.88mx4.88mx1.22m)
16
18ftx9ftx48in
(5.49mx2.74mx1.22m)
12
22ftx12ftx52in
(6.71mx3.66mx1.32m)
16
24ftx12ftx52in
18
B-A-A-A-A-C
(7.32mx3.66mx1.32m)
31.3ftx16ftx52in
24
B-A-A-A-A-A-A-C
(9.56mx4.88mx1.32m)
PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE.
CHOOSE THE CORRECT LOCATION
NOTE:
The pool must be set up on a completely flat and level surface. Please do not
install the pool if the surface is inclined or sloped.
Correct conditions to set up the pool:
• The selected location has to be capable of uniformly supporting the weight for the entire time the
pool is installed, moreover the location must be flat and must be cleared of all objects and debris
including stones and twigs.
• We recommend positioning the pool away from any objects children could use to climb into the pool.
NOTE:
Position the pool near an adequate drainage system to deal with overflow or to
discharge the pool.
Incorrect conditions to set up the pool:
• On uneven ground the pool may collapse causing serious personal injury and/or damage to
personal property and will void the warranty and prevent any service claims.
• Sand should not be used to create a level base; the ground must be dug out if necessary.
• Directly under overhead power lines or trees. Be sure the location does not contain underground
utility pipes, lines or cables of any kind.
• Do not set up the pool on driveways, decks, platforms, gravel or asphalt surfaces. The selected
location should be firm enough to withstand the pressure of the water; Mud, sand, soft / loose soil
or tar are not suitable.
• Grass or other vegetation under the pool will die and may cause odors and slime to develop,
therefore we recommend removing all grass from the selected pool location.
• Avoid areas prone to aggressive plant and weed species that may grow through the ground cloth
or liner.
NOTE:
Check with your local city council for by-laws relating to fencing, barriers, lighting
and safety requirements and ensure you comply with all laws.
NOTE:
If have a filter pump, refer to the pump's manual for instructions.
NOTE:
The ladder must match the pool size and should to be used only for entering and
exiting the pool. It is forbidden to exceed the permitted payload of the ladder. Check regularly if the
ladder is properly assembled.
S-S-004354/21.0x28.5cm(矩形支架水池说明书 C版) JS-YF-2016-B-02553 英
Small
Big U-Support
U-Support Cap
Cap
Part No.
QTY
Part No.
QTY
Part No.
P61366
16
P61367
/
/
20
P61367
/
/
P61366
P61366
20
P61367
/
/
P61286
/
/
24
P61287
P61286
/
/
32
P61287
P61286
/
/
24
P61287
P61286
/
/
32
P61287
P61286
/
/
36
P61287
P61286
/
/
48
P61287
Top Rail Combinations
No. of Top Rail
Long Side
Short Side
A
B
C
D
E
B-A
C-D
2
2
2
2
0
B-E-A
C-D
2
2
2
2
2
B-E-A
C-D
2
2
2
2
2
D-F-F-E
D-E
0
0
0
4
4
D-F-F-E
D-F-F-E
0
0
0
4
8
B-A-A-C
D-E
4
2
2
2
2
B-A-A-A-C
E-D-F
6
2
2
2
2
E-D-F
8
2
2
2
2
D-F-F-E
12
2
2
2
2
Sleeve for
Installation
C-connector
Assembly of the Rectangular Frame Pool can be completed without tools.
Bestway Inflatables will not be responsible for damage caused to the pool due to mishandling or
QTY
Part No.
failure to follow these instructions.
8
P61365
1. Lay out all parts and check that you have the correct quantities as listed in the components list.
If you are missing any part do not assemble the pool, contact Bestway Customers Service.
8
P61365
2. Spread out the pool and make sure the pool is right side up, let it sit exposed to direct sunlight
for 1 hour or more so that the pool is more flexible during set up.
8
P61365
3. Place the pool near an adequate drainage system to deal with overflow water and ensure the
pool's inlet A and outlet B are correctly positioned to allow your filter pump to connect to a power
8
P61285
source.
NOTE:
8
P61285
Do not use extension power cords to power your pump.
ATTENTION:
P61285
8
4. Insert the stopper plugs into inlet A and outlet B on the wall from the inside of the pool.
8
P61285
NOTE:
For pool with connection valve, please refer to the connection valve installation on
8
P61285
following page.
5. Assemble the Top Rails. Start with the long side of the pool, begin by sliding Top Rail B into the
8
P61285
pool sleeve. Connect Top Rail A or Top Rail E to Top Rail B, ensure the spring-loaded pins snap
into the pre-drilled holes. Be sure to reference the Top Rail Combination Chart to determine the
correct configuration for your pool. Continue connecting and inserting additional Top Rails. Be
sure to line up the holes in the rails with the holes on the sleeves. (See Fig.1)
6. Insert the C-Connectors into the Top Rails. (See Fig. 2.1/2.2)
7. Install the U-Support; first insert the U-Support through the Pole Support at the bottom of the
pool (See Fig. 3.1/3.2), then insert the two ends of the U-Support into the exposed holes on the
Top Rail (See Fig. 3.3), ensure the spring-loaded pins snap into position. Repeat this procedure
for the remaining U-Supports.
NOTE:
Complete one side of the pool before moving to the other side.
8. Pull the bottoms of the U-Support outward away from the liner and make the Pole Support taut.
Repeat this procedure for remaining U-Supports.
9. Ensure drain valve is firmly closed.
10. Put 1in to 2in (2.5cm to 5cm) water in the pool to cover the floor. Once pool floor is slightly
covered, gently smooth out all wrinkles. Start in the center of the pool and work your way
clockwise to the outside. (See Fig.4)
Fig. 1
Fig. 2.2
C-Connector
F
0
4
0
4
Fig. 3.1
0
4
4
4
4
4
0
4
Fig. 4
2
4
2
4
4
4
Connection Valve Assembly
For pool with connection valve (See Fig.6)
Fig.6
4
Do not drag the pool on the ground, this can damage the pool.
Fig. 2.1
Fig. 3.2
Fig. 3.3
Fig. 5
A
B
S-S-004354
Publicité
