Packing List - Riello ChronoRiello 7D Wireless WR Manuel D'installation Et D'utilisation

Status mode selection MOdE: rotate to change the thermostat mode
between AUTO, PARTY, and OFF, press to save. The press from
status mode automatically escapes from menu.
Economy temperature selection ECOt: Rotate to select the desired
economy temperature and press to enter. This temperature is used
when programming time is OFF in AUTO status mode.
Heating and cooling mode selection I - -S: Rotate to select the ther-
mostat mode between I (heating) and S (cooling), press to save.
The selected mode is identified on the display with the presence of
the radiator icon in AUTO mode (radiator icon ON means heating
mode, radiator icon OFF means cooling mode). In cooling mode the
request versus the chiller appliance remain ON till the room temper-
ature moves below the target.
Time of the day: rotate to change the hours, press to save. Move to
minutes; rotate to change minutes, press to save.
Day of the week: rotate to change the day, press to save.
Programmed times day 1-7: rotate clockwise to set hour ON, rotate
anticlockwise to select hour OFF. Clockwise and anticlockwise rota-
tion move ahead the time. Press to save. Rotate clockwise to move
to the following day. It is possible to program together days 1...5 and
days 6-7 with the same pattern in a single operation.
PL: rotate to select the password value, press to enter inside the
technical menu. Rotate to select the parameters:
1 = COUP - ENCODING between the receiver and the transmitter
2 = CH - RADIO FREQUENCY modification
3 = FRST - frost protection temperature selection
4 = H ON - hysteresis ON value selection
5 = HOFF - hysteresis OFF value selection
6 = SENS - TEMPERATURE SENSOR ON-OFF.
The temperature sensor can be ativated or deativated
7 = CALI - calibration of the temperature sensor
8 = FACT - restore factory settings
9 = EXIT - escape from technical menu
Exit: escape from main menu.
INSTALLATION AND OPERATING INSTRUCTIONS
Unlike the conventional thermostat, this control separates the func-
tion in two units. The receiver serves for wiring connections and
heat on/off control. The transmitter serves as the user interface and
for temperature sensing/control. The two units are linked by radio
frequency (RF). The RF communication is two directions from the
transmitter to the receiver; therefore if transmitter-receiver are not
coupled, alarm of missing communication is visible on the transmit-
ter display.
THE TRANSMITTER is a wall-mounted thermostat.
The transmitter can be located wherever a conven-
tional room thermostat would normally be sited. No
wiring is required, as the transmitter is battery pow-
ered.
THE RECEIVER is connected to the boiler, and can
replace a conventional mechanical or electronic time
clock. The receiver arrives pre-cabled and ready to
be fixed, therefore it is not necessity to open the
receiver casing. The receiver is equipped with a
transparent bubble button that incorporates the but-
ton function, the green led function and the red led
function.
Button functions:
1. Press once: manually switch ON the heating (relay closed), press
again to switch OFF.
2. Press for 3 seconds: encoding procedure start up. After success
coupling there is an automatically exit from the procedure (see the
PL menu at point 1-COUP).
Receiver led: colors and functionality
GREEN LED RED LED
F05
F1
ON
STATUS
Relay = closed
(only for ON/OFF connections)
Relay = open
(only for ON/OFF connections)
OTBus connection = OK
(for OTBus connection)
GREEN LED RED LED
ON F1
F05
F1 ON
ON (OTBus)
F1 F1
LED
ON = remains on
F05 = quick flash (every 0.5 seconds)
F1 = slow flash (every 1 second)
NOTE 1 FOR RECEIVER: when the receiver is manually moved to
the ON or OFF relay position (heating request ON or OFF), after few
seconds (at least 100 secs.) the relay position will move according
the transmitter request. If it is required for a permanent ON or OFF
position, please use the transmitter functionality.
NOTE 2 FOR RECEIVER: in case of missing radio communication
(see errors paragraph), the receiver relay moves automatically to the
ON position (after 10 minutes of missing communication) whatever
the transmitter request was (led irregularly blinking). However it is
possible manually move the relay position (the heat request) to the
OFF or ON position permanently by pressing the receiver transpar-
ent button. The selected position is indicated by the red or green
light irregularly blinking. Once the radio communication has been
reativated the receiver will revert to work according the transmitter
requests.

PACKING LIST

RF receiver with 6 wire cable fitted
RF transmitter
Screws and wall plugs (drill 5 mm)
Adhesive magnetic fitted
Instructions
Batteries 1,5 AAA
BOILER PREPARATION
Isolate the appliance from the electrical supply and remove the ap-
pliance casing and PCB cover (refer to boiler installation instructions
for specific details).
The receiver can be provided with or without a male plug according
the product code ordered and according the availability of female
counterpart on the boiler side. The version without male plug is sup-
plied with spade terminals.
Receiver with male plug fitted
plug - male Connect the male plug (4 pins) of the receiver to the
female plug on the boiler (pre-wired on specific boiler
L N I O
models).
M
Receiver with spade terminals
Connect the spade terminals from the receiver to the PCB terminals
(room thermostat terminal black & black, open term (OT) bus red
& red (alternative to room thermostat connection), main supply
terminals blue and brown on the main boiler supply socket) - figure
below for a sample boiler connections.
Blue = main supply 230 Vac = neutral N
Brown = main supply 230 Vac = line L
Black & Black = room thermostat = I-O (TA)
Red & Red = OpenTherm = OT bus
See picture for the receiver internal connections.
L N I O
OT - OpenTherm
Remove the bridge
Black RF wires connections
M
CN6
CN5
CN13
P1
IMPORTANT: the link-wire (if fitted) must be removed from room
thermostat terminals
IMPORTANT: Secure the receiver wiring harness to the internal
boiler cable anchors.
4
STATUS
Boiler alarm
(only for OTBus connection)
Network or RF error
Encoded RF mode active
QTY
1
1
2
1
1
2
230 V
N L
M3
F
CN12
1
JP5 JP4 JP3 JP2 JP1
brown RF
JP6
blue RF
P2
P3