Hurricane PS 2000-40E Mode D'emploi page 18

Anleitung PS 2000-40 E 25.11.2004
GB
at this stage. After running in, check chain tension
and retension if necessary.
9. Filling in chain oil
To prevent dirt getting inside the tank, clean the oil
tank cap (3) before opening. Check the contents of
the oil tank during sawing work by checking the oil
gauge (21). Close the oil tank cap (3) tightly and
wipe away any spills.
10. Chain lubrication
To prevent excessive wear, the saw chain and chain
bar must be evenly lubricated during operation.
Lubrication is automatic. Never work without chain
lubrication. If the chain runs dry, the entire cutting
apparatus will quickly become severely damaged. It
is therefore important to check both chain lubrication
and the oil gauge before every use (Fig. 9).
Never use the saw when the oil level is below the
„Minimum" mark (Fig. 9).
Minimum - When only approx. 5 mm of oil is visi-
ble at the lower rim of the oil gauge (21), you
must top up with oil.
Maximum - Top up with oil until the window is
full.
11. Checking the automatic lubrication
Before commencing work, check the automatic chain
lubrication and oil gauge. Switch on the chainsaw
and hold it above light-colored ground. Be careful not
to allow the chainsaw to touch the ground. For safety
reasons it is best to keep a clearance of at least 20
cm. If you now see growing traces of oil, the chain
lubrication system is working correctly. If there are no
traces of oil at all, try cleaning the oil outlet (4), the
upper chain tensioning borehole (14) and the oil
duct, or contact your Customer Service (Fig. 3).
Regulating the oil flow
Adjust the oil flow by turning the oil regulating screw
(23). In the case of damp and soft wood the oil flow
can be decreased (turn the oil regulating screw
clockwise); in the case of dry, hard would more oil is
required for lubrication (turn the oil regulating screw
anti-clockwise)
12. Chain lubricants
The service life of saw chains and chain bars
depends to a large extent on the quality of the lubri-
18
10:43 Uhr Seite 18
cant used. Old oil must not be used! Use only envi-
ronment-friendly chain lubricant. Store chain lubri-
cant only in containers which comply with the regula-
tions.
13. Chain bar
The chain bar (8) is subjected to especially severe
wear and tear at the nose and on the bottom. To
avoid one-sided wear and tear, turn the chain bar
over (8) every time you sharpen the chain.
14. Chain wheel
The chain wheel (12) is subjected to especially high
wear and tear. If you notice deep wear marks on the
teeth, the chain wheel must be replaced. A worn
chain wheel curtails the service life of the saw chain.
Have the chain wheel replaced by a specialist dealer
or your Customer Service.
15. Chain guard
The chain guard (20) must be clipped onto the chain
and sword as soon as the sawing work has been
completed and whenever the machine has to be
transported.
16. Chain brake
In the event of kick-back, the chain brake will be
actuated via the front finger guard (2). The front fin-
ger guard (2) is pushed forwards by the back of the
hand and this causes the chain brake to stop the
chainsaw, or rather the motor, within 0.10 s.
17. Releasing the chain brake
To be able to use your chainsaw again, you must
release the saw chain again. First switch off the
machine. Then push the front finger guard (2) back
into the vertical position until it locks in place. The
chain brake is now fully functional again.
18. Sharpening the saw chain
You can have your saw chain sharpened fast and
correctly by specialist dealers, from whom you can
also obtain chain sharpening equipment to enable
you to sharpen the chain yourself. Please follow the
corresponding operating instructions.
Take care of your tools. Keep your tools sharp
and clean to enable you to work well and safely.