Intended Use; Unpacking Your Tool; Before Use; Operation - GMC GDD12 Instructions Originales

Intended Use

Battery operated general-purpose impact driver, suitable for light to medium duty tasks,
driving nuts and bolts.

Unpacking Your Tool

• Carefully unpack and inspect your new sander. Familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool

Before Use

Removing a battery
• To remove the Battery (8) from the impact driver, press the Battery Release (9), then slide
the Battery off the Hand Grip (7)
WARNING: DO NOT try to remove the Battery without pressing the Battery Release button.
The drill or Battery could be damaged.
Fitting a battery
1. To fit a charged battery, slide it into the Hand Grip (7) of the drill until it clicks and
locks into position
Note: Make sure the Battery and Impact Driver are lined up correctly. If the Battery does
not slide into the Impact Driver easily, don't force it. Instead, slide the Battery out of the
Impact Driver again, check the top of Battery and the Impact Driver battery slot are clean and
undamaged and that the contacts are not bent.
Setting up the battery charger
1. If fitted, remove any battery from the Battery Charger (10)
2. Insert the Mains Plug (11) into a suitable mains socket
Note: The Green LED (12) on the Battery Charger will illuminate to indicate that the charger
is ready to charge the battery.
WARNING: ONLY use this charger to charge the supplied battery or additional purchased
batteries that are specifically designed for this tool.
WARNING: The charger is designed for indoor use only, and MUST NOT be used in damp
or wet conditions.
Charging the battery
WARNING: Failure to follow the correct procedure when charging batteries will result in
permanent damage.
Note: Normal charging time is 1 hour for a recently discharged battery. However, if the
Battery (8) has been left in a discharged state for some time, it may take up to 1.5 hours to
charge.
1. Slide a fully or partially discharged Battery into the Battery Charger (10)
Note: Make sure the Battery and Battery Charger are lined up correctly. If the Battery does
not slide into the Battery Charger easily, don't force it. Instead, remove the Battery, check the
top of Battery and the Battery Charger slot are clean and undamaged and that the contacts
are not bent.
2. Both the Green LED (12) and Red LED (13) will flash to show the Battery is being
assessed by the charger
3. Once charging commences, both LEDs will illuminate without flashing
4. When the Battery is fully charged only the Green LED will be illuminated
Note: If both LEDs are not constantly illuminated after the charger has assessed the Battery,
this indicates a fault condition. Recheck the Battery is fully inserted into the Battery Charger
(10). Remove any material that may have fallen into the charger's battery socket, and make
sure the contacts of both the Battery and the Battery Charger are clean, untarnished and not
damaged or bent.
Notes about battery charging:
• The battery should be charged at ambient temperatures between 10 and 40°C (ideally
around 20°C)
• After charging, allow 15 minutes for the battery to cool before use
• Ensure that the charger is disconnected from the mains supply after use, and is stored
correctly
• DO NOT leave batteries on charge for extended periods and NEVER store batteries on
charge
• The Battery Charger monitors battery temperature and voltage while charging. Remove
the Battery once charging has been completed to maximise charge cycles of the battery
and not waste power
• Batteries can become faulty over time, individual cells in the battery can fail and the
battery could short. The charger will not charge faulty batteries. Use another battery, if
possible, to check correct functionality of the charger and purchase a replacement battery
if a faulty battery is indicated
• DO NOT store Lithium-Ion battery packs in a discharged state long term. This can
damage the Lithium-Ion cells. For long-term storage, store batteries in a high charge state
disconnected from the power tool
• The capacity of batteries will reduce over time. After 100 charge cycles, the battery's
operation time and the maximum torque performance of the drill will slightly reduce. This
decline will continue until the battery has minimal capacity after 500 charge cycles. This is
normal and not a fault with the battery pack
Fitting a driver bit
WARNING: DO NOT fit any attachment with a maximum speed lower than the no load speed
of the machine.
1. Pull the Collar (2) of the Hex Bit Holder (1) forward, and insert the bit
2. Release the Collar
3. Pull on the bit to check that it is securely fitted. If the bit is not secure, repeat the
above procedure
Note: Make sure screwdriver bits used are hardened and suitable for use with an impact
driver.

Operation

Direction control

WARNING: NEVER change the direction of rotation while the tool is running. This may cause
permanent damage to the tool.
• The direction of rotation can be set using the Forward/Reverse Switch (5)
• For anti-clockwise rotation, push the switch to the right
• For clockwise rotation, push the switch to the left
Note: When the Forward/Reverse Switch (5) is in the central position, the drill is locked and
cannot be switched on. Use this setting as a safety feature to prevent the drill from being
switched on accidentally.
Switching on/off
WARNING: ALWAYS wear adequate personal protection equipment when setting up and
operating this machine.
1. To start the drill, squeeze the Trigger Switch (6)
2. The built-in Work Light LEDs (3) will illuminate when the Trigger Switch is squeezed
7
GB