Routine Maintenance; Lubrication; Recommended Lubricants; After The First 8 Hours Service - breviglieri b25s Manuel D'utilisation, Entretien Et Pièces De Rechange

SECTION 5
Maintenance

5.1 ROUTINE MAINTENANCE

The various routine maintenance operations are described be-
low. Remember that lower running costs and longer machine life
depend on continual compliance with these instructions.
WARNING
Before proceeding with any operation, make sure that the
machine is parked on a flat surface. Prevent it from moving
by placing chocks under the wheels.
Servicing, adjusting and the operations required to prepare
the machine for work must be carried out with the tractor
and the driveline detached from the machine.
The servicing frequencies indicated in this manual are in-
dicative and refer to normal conditions of use. They may there-
fore vary depending on the type of service, whether the envi-
ronment is dirty or not, seasonal factors, etc. The servicing
operations must obviously be carried out more frequently in
heavier duty service conditions.
- Before injecting lubricating grease into the grease nipples,
carefully clean these latter to prevent mud, dust or foreign
bodies from mixing with the grease as this would reduce
or even annul its lubricating effects.
Injection into the greasing points of a large quantity of
grease at high pressure can damage the bearing protec-
tion. This operation must therefore be carried out with the
greatest care.
- Lubricate and grease all the required points, including the
chains.
- Use oil of the recommended type for topping up and
changes.
Keep all lubricants well away from children's reach.
Carefully read the warnings and precautions on the lubricant
containers.
The operator should thoroughly wash himself after using lu-
bricants.
Dispose of used oil in compliance with the anti-pollution laws.

5.2 LUBRICATION

Lubrication of any machine with parts that turn and/or rub together
is a vitally important task for the life and functionality of the actual
machine itself. Lubrication must therefore be carried out system-
atically and at the required intervals. The frequencies given refer
to machine use in a normal environment. If this machine is used
in heavier duty conditions, it must naturally be lubricated more
frequently.
CAUTION
DANGER
b25s
KEY to Fig. 9
1 Housing oil fill plug
2 Housing oil level
3 Oil fill plug with level
4 Oil drain with final drive
5 Grease nipple for rh rotor support

5.2.1 RECOMMENDED LUBRICANTS

- For the final drive (or gearbox) and for the side transmission
gears, the Manufacturer recommends: AGIP ROTRA MP SAE
85W/140 OIL or an equivalent type complying with API-GL5/
MIL-L-2105C specifications.
- For all greasing points, the Manufacturer recommends: AGIP
GR MU EP 2 grease or an equivalent type.
When servicing the driveline, strictly comply with the instruc-
tions given by the driveline Manufacturer, in the specific opera-
tion and maintenance manual with which each driveline is
equipped.

5.2.2 AFTER THE FIRST 8 HOURS SERVICE

Each new machine must be checked after the first 8 hours ser-
vice. proceed in the following way:
- Check the general condition of the machine.
- After having checked the tines for wear, fully tighten the bolts
that fix the tines in place.
- Check to make sure that all the bolts on the machine are tight.

5.2.3 EVERY 20 HOURS SERVICE

- Check to make sure that the tine bolts are tight.
- Grease the driveline, the roller adjuster screw and the roller
supports.

5.2.4 EVERY 100 HOURS SERVICE

- Check the level of the oil in the final drive housing. Top up the
level if necessary.
- Check the level of the oil in the side housing. Top up the level if
necessary. The correct oil level is reached when oil spills from
the hole of the level plug (2 Fig. 9).

5.2.5 EVERY 500 HOURS SERVICE

- Change the oil in the final drive housing after every 500 hours
service or at least once a year.
- Check to make sure that the driveline clutch is fully efficient.
Have the clutch overhauled and the plates replaced by a spe-
cialized workshop if necessary.

5.3 PREPARING FOR STORAGE

Proceed with the following operations at the end of the season or
if the machine is to remain idle for a long period of time:
- Wash all fertilizers and chemical products from the machine
and dry it.
- Carefully check the machine and replace any damaged or worn
parts.
- Fully tighten all the screws and bolts, particularly the ones that
fix the tines.
- Thoroughly grease the machine and then cover it with a tarpau-
lin and store it in a dry place.
If these operations are carried out with care, it will be all to
the user's advantage as the machine will be in optimum con-
ditions when needed again.
- 22 -