Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
- When the user has failed to comply with the instructions in this
manual.
Damage deriving from negligence, carelessness, bad and im-
proper use of the machine or incorrect manoeuvres by the opera-
tor are also excluded from the warranty. Removal of the safety
devices with which the machine is equipped shall automatically
void the warranty and relieve the Manufacturer from all liability in
merit.
The warranty also becomes void if spurious spare parts are used.
Even when covered by the warranty, the machine must be re-
turned Carriage Free.
1.3 DESCRIPTION OF THE MACHINE AND USE
Steerage hoe b25s bears «CE» marking in compliance with
the European Union standards described in Directive 98/37/
EC and successive modifications, as indicated in the decla-
ration of conformity with which each machine is provided.
1.3.1 DESCRIPTION
The machine mainly consists of a metal framework housing the
central hitch with three-point linkage (1 Fig. 1) and a bladed rotor
installed in the lower part (11 Fig. 1) driven by a chain or gears
situated in the side housing (7 Fig. 1). The power required to op-
erate the machine is transmitted by the tractor via a driveline (with
CE marking) which meshes with the gearbox/final drive unit in a
central position (5 Fig. 1), and is subsequently transmitted to the
gears by a drive shaft.
KEY to Fig. 1
A Front part
B Rear part
C Left side
D Right side
1 Three-point hitch linkage
2 Upper 3-point hitch
3 Machine lifting point
4 Driveline support
5 Final drive unit
6 Side transmission unit
7 Safety guards
8 Hood
9 Bearing stand
10 Bladed rotor
11 Lower 3-point hitch
12 Power take-off
13 Driveline shield
14 Work depth adjuster skid
15 Skid adjuster bolt
16 Identification plate
1.3.2 USE
Steerage hoe b25s has solely been designed for use in agri-
culture in order to work and break up the soil.
One single operator seated on the tractor is able to carry out
the various tillage operations.
Any other use of the machine differing from the explanations
given in this manual relieves for Manufacturer from all and
every liability for deriving damage to persons, animals or
property.
b25s
1.4 IDENTIFICATION
Each machine is provided with an identification plate (16 Fig. 1)
with the following data:
- Manufacturer's name and address;
- «CE» marking;
- A) Machine model;
- B) Machine version;
- C) Serial number;
- D) Weight (in Kg);
- E) Year of manufacture.
The data on the identification plate of the machine should be cop-
ied into the last page of this manual and must always be stated
when spare parts and/or assistance are required.
Standard machine supply includes:
- Operation and maintenance manual for the machine;
- «CE» declaration of conformity.
1.5 NOISE LEVEL
The sound level has been measured in compliance with
current standards, with the following results:
- Acoustic pressure LpAm (A) .......................... dB
- Acoustic power LwA (A) ................................. dB
1.6 TECHNICAL SPECIFICATIONS
Model
HP
b25s 85
10-20
b25s 105
15-25
b25s 125
20-30
SECTION 2
General safety notes
2.1 SAFETY NOTES
The user must inform his personnel about the risks deriving from
accidents, about the safety devices installed to safeguard the
operator and about the general accident-preventing regulations
established by the Directives and by the laws in force in the coun-
try where the machine is used.
It is therefore essential for operators to carefully read this manual,
particularly the safety notes, and to pay great attention to opera-
tions which could be particularly hazardous.
The Manufacturer declines all and every liability for failure to
comply with the safety and prevention regulations given in
this manual.
Pay attention to this symbol when it appears in the manual. It
indicates a possible danger situation.
- 16 -
Machine width
Tines
Kg
work. dimens.
N°
97
16
145
85
117
20
160 105
137
24
175 125
83.6
98.5
Kg/max
Depth
5-15
160
5-15
175
5-15
190
Publicité
Chapitres
Table des Matières
