Applications - Monacor ESUB-6C/WS Notice D'installation

PA Subwoofer for Wall and
Ceiling Installation
These instructions are intended for installers
with specific knowledge in sound reproduc-
tion using 100 V technology. Please read the
instructions carefully prior to installation and
keep them for later reference.

1 Applications

This subwoofer is specially designed for PA
systems. It is used to improve bass repro-
duction. The subwoofer is provided with a
transformer for operation in 100 V systems,
but it can also be directly connected to a low-
impedance amplifier output. A rotary switch
behind the speaker grille is used to match the
connected load.
2 Important Notes
The speaker corresponds to all relevant di-
rectives of the EU and is therefore marked
with .
•
The speaker is suitable for indoor use only.
Protect it against dripping water, splash
water and high air humidity. The admissi-
ble ambient temperature range is 0 – 40 °C.
•
For cleaning only use a dry, soft cloth; never
use water or chemicals.
1
2
1
2
5 ×
1
•
No guarantee claims for the speaker and
no liability for any resulting personal dam-
age or material damage will be accepted
if the speaker is used for other purposes
than originally intended, if it is not safely
installed or not correctly connected, or if it
is overloaded.
If the speaker is to be put out of op-
eration definitively, take it to a local
recycling plant for a disposal which
is not harmful to the environment.
3 Installation
WARNING During operation, there is a
Always observe the load of the PA amplifier
by the speakers. An overload may damage
the amplifier!
1) Before installing the subwoofer, switch off
the PA amplifier so that the speaker cable
will not carry any voltage!
2) Saw a mounting hole (⌀ 268 mm) into the
ceiling or wall. The mounting depth must
be 255 mm.
1
3
1
4
⏚
0 +
1
∅ 268
255
1
∅ 310
hazard of contact with a dan-
gerous voltage of up to 100 V
at the speaker cable. Installa-
tion must be made by skilled
personnel only.
5
10 cm min.
6
7
2
Specifications
Power rating
Music power
Frequency range
SPL
Max. SPL
Radiation angle
Type of speaker
Ceiling thickness
Mounting hole
Mounting depth
Dimensions
Weight
Connection
5 min.
Ambient temperature
32 max.
10
All rights reserved by MONACOR
No part of this instruction manual may be reproduced in any form
or by any means for any commercial use.
3) Remove the speaker grille to access the
mounting screws and the rotary switch
for the connected load.
4) Use a screwdriver to adjust the rated load
for 100 V operation on the rotary switch.
For direct operation at a low-impedance
amplifier output, set the switch to the
position "4 Ω".
CAUTION! Never use the position
"4 Ω"when the speaker is operated in a
100 V system: The speaker and possibly
also the amplifier will be damaged.
5) For ceiling installation, always attach the
safety rope (5) provided to secure the sub-
woofer.
a) Press on the locking sleeves (6) to pull
the rope from the rope clip (7).
b) Attach the rope to a mechanically stable
spot (see drawing).
c) Adjust the rope length in such a way
that the fall distance will be as short
as possible if the subwoofer falls from
the ceiling.
d) After connecting the subwoofer, attach
the spring hook of the rope to the eye-
bolt (2) of the subwoofer.
6) Pull the speaker cable through the cable
clip (3), connect the cable to the screw
terminals "0" and "+" (4) and use the
cable clip to fasten the cable.
7) Make sure that the five clamping pieces
(1) are in their initial positions (see top
view) before inserting the speaker into the
mounting hole. Insert the speaker into the
hole and fasten the mounting screws to
secure the speaker.
8) Replace the speaker grille.
Subject to technical modification.
ESUB-6C / WS
100 V: 40 / 20 / 10 W
4 Ω: 55 W
110 W
45 – 280 Hz
88 dB (1 W/1 m)
104 dB
180°
band-pass subwoofer with
16 cm (6") long-excursion driver
5 – 32 mm
⌀ 268 mm
255 mm
⌀ 310 mm × 265 mm
5 kg
ceramic screw terminals
0 – 40 °C
INTERNATIONAL GmbH & Co. KG.
®
3