Safety Precautions - Vollrath 59500 Mode D'emploi

S P
afety recautionS
To ensure safe operation, read the following statements and
understand their meaning. This manual contains safety precautions
which are explained below. Please read carefully.
WARNING
Warning is used to indicate the presence of a hazard that can cause
severe personal injury, death, or substantial property damage if the
warning is ignored.
CAUTION
Caution is used to indicate the presence of a hazard that will or can
cause minor personal injury or property damage if the caution is
ignored.
NOTE
Note is used to notify people of installation, operation, or
maintenance information that is important but not hazard-related.
For Your Safety!
These precautions should be followed at all times. Failure to follow
these precautions could result in injury to yourself and others.
To reduce risk of injury or damage to the unit:
„ Plug only into grounded electrical outlets matching the nameplate rated
voltage.
„ As a precaution, persons using a pacemaker should stand back 12"
(30 cm) from an operating unit. Studies have shown that the induction
element will not disrupt a pacemaker.
„ Keep all credit cards, driver liscences and other items with a magnetic
strip away from an operating unit. The unit's magnetic field will damage
the information on these strips.
„ The heating surface is made of a strong, non-porous material.
However, should it crack or break, stop using and immediately unplug
the unit.
„ Do not leave an empty pan on an operating unit.
„ Unit should only be used in a flat, level position.
„ Unplug unit and let it cool before cleaning or moving.
„ Do not touch the cooking surface. It remains hot after the unit is turned
off.
„ Do not spray controls or outside of unit with liquids or cleaning agents.
„ Unplug when not in use.
„ Keep unit and power cord away from open flames, electric burners or
excessive heat.
„ Do not heat sealed cans or containers as they may explode.
„ Do not operate unattended.
„ Closely supervise units operating in public areas and/or around
children.
„ Do not operate if unit has been damaged or is malfunctioning in any
way.
„ Do not place any objects inside the air intake or exhaust panels.
„ Do not place weight on the control knob.
2 O ' M
peratOr s anual
f P
unction and urPoSe
This unit is intended to be used with induction-ready cookware (see below)
with a flat, ferrous base measuring 4-1/2" (11.4 cm) to 10-1/4" (26 cm) wide.
This unit is intended for use in commercial foodservice operations only. It is
not intended for household, industrial or laboratory use.
I R c
nductIon eady ookwaRe
„ Ferrous stainless steel
„ Iron
„ Cast iron
u c
nsuItable ookwaRe
„ Cookware with a base less than 4-1/2" (11.4 cm)
„ Pottery, glass, aluminum, bronze or copper cookware
„ Cookware with any type of footed base
i
nStallation
This unit is to be used on a flat, level surface.
c
outeRtop
NOTE:
This unit is not designed to be inclosed or built into any area.
There must be a minimum of 4" (10 cm) of space between the rear
of the induction range and any surrounding surface.
There must be 15 mm (0.6"), except 20 mm (0.787") for item 6950020
or 6951020, between the bottom of the induction range and any
surrounding surface.
Sufficient airflow must be allowed around the unit. Blocking the
airflow could cause the unit to overheat.
1. Place the induction range/warmer on a flat stable surface.
2. Plug the power cord into a grounded electrical outlet with the matching
nameplate rated voltage.
NOTE:
Using a voltage other than the nameplate rated voltage will cause
damage to the unit. Incorrect voltage, modification to the power
cord or electrical components can damage unit and will void the
warranty. Induction units are to use a separate dedicated circuit.
d -I
Rop n
NOTE:
There must be a minimum of 2" (5 cm) of space between all four
sides of the induction range and any surrounding surface.
There must be 12" (30.5 cm) between the bottom of the induction
range and any surrounding surface.
Sufficient airflow must be allowed around the unit. Blocking the
airflow could cause the unit to overheat.
1. Choose a flat, level countertop for the mounting surface.
2. Measure the area for the cutout, including the countersink area. The
unit is designed to be countersunk. The depth of the surface around the
cutout must be reduced to allow for the countersink. See the illustration
below.